Subscribe to Our Youtube Channel
Related Manuals for Handler 16B
Summary of Contents for Handler 16B
- Page 1 16B RED WING LATHE & CHUK/CHANGER OPERATING MANUAL IMPORTANT INSTRUCTIONS [06/2009] WARNING! FOR YOUR SAFETY PLEASE READ INSTRUCTIONS BEFORE OPERATING TOOL & WEAR EYE PROTECTION FD.06/2009...
- Page 2 THANK YOU FOR PURCHASING A HANDLER PRODUCT HANDLER’s Red Wing Lathe. Thank you for purchasing a Open the carton and inspect all contents. Your 16B was inspected several times during the manufacturing process, plus as a completed unit after it was built and tested.
-
Page 3: Safety Instructions
REPAIR OR REPLACE DAMAGED OR WORN CORD IMMEDIATELY. DO NOT ExPOSE TO RAIN OR USE IN DAMP LOCATIONS. ADVERTISSEMENT: NE PAS ExPOSER A LA PLUIE ET NE PAS UTILISER DANS LES EMPLACEMENTS HUMIDES. 16B Red Wing Lathe & Chuk/Changer Instruction... - Page 4 NOTE: Many Red Wing polishing motors are shipped with 1/2” straight shafts. Chucks used on Red Wing Polishing motors equipped with a 1/2” straight shaft utilize a set screw to hold the chuck in position. Make certain to tighten this securely. 16B Red Wing Lathe & Chuk/Changer Instruction...
-
Page 5: Important Notice
Your Chuk/Changer has been manufactured, assembled, adjusted and tested with the utmost of care to insure that you will receive it in perfect condition. We ask that you carefully read and follow these step by step instructions. 16B Red Wing Lathe & Chuk/Changer Instruction... - Page 6 NOTE: Should the clutch handle stop before the 9:30 o’clock position, the adapter set screws should be loosened and the QUESTIONS? Review FAQ section on our website at: entire chuck assembly pulled away from the the lathe. www.handlermfg.com or call 1-908-233-7796. 16B Red Wing Lathe & Chuk/Changer Instruction...
-
Page 7: Installation And Maintenance
If squeaking persists and there is a presence of excessive amounts of dust around the clutch area, the adapter is improperly mounted, causing misalignment of the clutches. Refer to installation instructions for your model lathe. 16B Red Wing Lathe & Chuk/Changer Instruction... -
Page 8: Operation And Care Instructions
See instructions under removing chuck from lathe. Grasp the steel clutch plate to keep it from turning while you remove the collet. *However, make certain collets have been properly cleaned. Dirty collets may also cause chuck slippage. 16B Red Wing Lathe & Chuk/Changer Instruction... -
Page 9: Care And Maintenance
ACCESSORIES Handler manufactures a full line of Chucks, Protective Hoods, Shields, and Dust Collectors for use with your Red Wing motor. Handler chucks are precision manufactured to fit onto your Red Wing motor. A few of these are described below. - Page 10 Note: Specify a No. 20 L or R chuck for a polishing motor with a straight 1/2” shaft. Handler has designed and built a full line of automatic chucks which will adapt to your Red Wing or other polishing motors. Handler’s automatic chucks are durable and built to save processing time and money.
-
Page 11: Parts List
Rotor - No.21 Screws for above (set, 4) specify whether 1 or 2 speed lathe No.22 Lubri-Plate - 1 3/4 oz tube No.9 Centrifugal Switch - specify whether 1 or 2 speed lathe 16B Red Wing Lathe & Chuk/Changer Instruction... - Page 12 OSHA RECOMMENDED SHIELDS Handler has designed and built a full line of automatic chucks which will adapt to your Red Wing or other polishing motors. Handler’s automatic chucks are durable and built to save processing time and money. PROTECTIVE SHIELDS AND HOODS...
-
Page 13: Parts And Accessories
Clutch complete for all Baldor lathes No.21HS Screw only, 2-64 for No. 21H No.10RM Clutch complete with bearing for all No.22 Bearings Robbins-Myers lathes No.10R Clutch complete with bearing for all Ritter lathes 16B Red Wing Lathe & Chuk/Changer Instruction... -
Page 14: Returning Goods
IMPORTANT NOTICE WHAT SHOULD YOU DO TO RETURN GOODS 1. Our terms of sale are F.O.B. our plant. Handler makes every effort to insure the proper delivery of goods, but we cannot guarantee the carrier’s performance. Each product is tested and inspected for proper performance prior to leaving our facility. -
Page 15: Grounding Instructions
Tie back 14. Avoid Accidental Starting this and any other long hair or use a proper hair net. appliance. Be sure switch is OFF when plugging in. 16B Red Wing Lathe & Chuk/Changer Instruction... -
Page 16: Warranty
WARRANTY This HANDLER product is warranted to be free from defects in material and workmanship, when used under the conditions recommended by the manufacturer, and/or the purpose for which the product was intended, for a period of 12 months from the date of shipment from factory to job site of original owner.
Need help?
Do you have a question about the 16B and is the answer not in the manual?
Questions and answers