Panasonic L-SC3235BX Operation Instruction Manual
Panasonic L-SC3235BX Operation Instruction Manual

Panasonic L-SC3235BX Operation Instruction Manual

Ip video intercom kit

Advertisement

Quick Links

Operation Instruction
VL-VC3535BX
Panasonic
VL-MC3035BX
Thank you for purchasing this product.
- Read these instructions carefully for optimum
performance and safety before use.
- Keep this manual for future reference.
IP Video Intercom Kit
Model : VL-SC3235BX/
VL-SC3235WX/
VL-VC3535BX/
VL-MC3035BX/
VL-MC3035WX
Content
Printed in China
R
1
2
3
10
12
15
16
17
23
27
30

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the L-SC3235BX and is the answer not in the manual?

Questions and answers

Summary of Contents for Panasonic L-SC3235BX

  • Page 1: Table Of Contents

    8.Quick parameter configu- ration 9.Common functions of Room Monitor 10.Parameter settings of Room Monitor VL-VC3535BX Panasonic VL-MC3035BX 11.Function introduction of Door Station Thank you for purchasing this product. - Read these instructions carefully for optimum performance and safety before use.
  • Page 2: Including Items

    Door Station VL-VC3535BX Standard POE. Note: Panasonic IP Video Intercom model compatibility is listed as Power connector: Connect PoE Splitter above. Please be aware that models not listed may not be compatible round plug DC source to 2 Wire connector.
  • Page 3: Important Information

    (1) Use standard POE(IEE 802.3af compliant);or described in the documentation may expose you to dangerous (2) Use the dedicated Panasonic Power Supply Unit(VL- voltages and other risks. PC3400BX or VL-PC3430BX) ・Do not touch the product or the power supply unit during an...
  • Page 4: Important Safety Instructions

    ・Always connect power cables to the appropriate connection ・It is generally understood that "privacy" refers to the ability of an terminals. Incorrectly connecting the power cables may damage individual or group to control the dissemination of information about the power supply unit. themselves, allowing it to be known only to those they choose to share it with.
  • Page 5 To the maximum extent permitted by ‒ When user information is stored on a computer, the confidential- applicable law, Panasonic assumes no liability for any direct or indi- ity of that information becomes the responsibility of the installer.
  • Page 6: Appearance Of Device

    Microphone Screen Speaker Device 15.9mm MicroSD Removal ・Panasonic may not be liable for damages due to external factors Card Slot Sensor such as power failures. 4.1.2 Door Station ・The recorded images may be lost when: ‒ Mishandled ‒ Electric shock or radio wave interference occurs.
  • Page 7: Solution Topology

    Power +): 5. Solution topology interface description 4.2.2 Door Station 5.1 Solution 1 Network CAT5e/6 (RJ45) Internet POE Network Power in- Panasonic VL-MC3035BX Room monitor Power In+ Door Open E-Lock Door State CAT5e/6 CAT5e/6 POE Network CAT5e/6 Device Removal Sensor...
  • Page 8 5.2 Solution 2 The following is the device interface connection Power diagram for Solution 1 Supply Internet CAT5e/6 Panasonic VL-MC3035BX Room monitor Power Supply CAT5e/6 VL-VC3535BX Door station Router Note:If you do not purchase a standard POE switch, you can choose this solution.
  • Page 9: Schematic View Of Device Installation

    CAUTION ・1.When installing the Door Station, it is recommended that the 6. Schematic view of device installation camera be positioned approximately 145cm from the ground to best capture visitor face. 6.1 Installation procedure of Room Monitor ・The Door Station shall not be installed in the sun exposure, rain, high temperature, snow/frost,...
  • Page 10: Quick Parameter Configuration

    b. User Password setting Operating voltage: 12 to 27VDC 2/4 User Password Operating power consumption: Standby power consumption: Password Enter 6-digits password Operating temperature: -20℃ to 60℃ Enter 6-digits password Comfirm password IP54 IP Rating: Next Back 8. Quick parameter configuration Note:This password is user password and Web login password.
  • Page 11: Device Name Setting

    d. Configuration Table setting Tap [Save] to save the network configuration of the device. 4/4 Configuration Table Device Name f. Device name setting Device No Status Room monitor 1 XXXXXXXXXXXXX 192.168.1.100 Name Set Network Set Number Set QR Binding Device Name Room monitor 1 Back Close...
  • Page 12 h. QR Code Binding Press and hold the Door Station call button for 10 seconds; the device enters the scanning and binding state. If the Door Station does not enter the binding state, check if the Door Station is Network Set Name Set Number Set QR Binding...
  • Page 13: Common Functions Of Room Monitor

    9. Common function of Room Monitor Tap this icon to freeze the touchscreen to Device enter the clean function. Cleaning Function 9.1 Introduction to functions of the main interface Tap this button to enter the settings buttons Settings function. (Function Bar) (Information Bar) Enters the security function interface.
  • Page 14 In the main interface, tap on [Monitor] button to In the [Video Intercom] interface, tap on the [Conta- cts] button. Users can call the indoor unit in the same enter the video monitoring interface. This interface Contacts home. The contents of the address book are automati- displays a list of devices capable of being monitored, cally recognized by the system and added to the device.
  • Page 15: Parameter Settings Of Room Monitor

    10. Parameter settings of Room Monitor 10.4 Description of display settings 10.1 Main interface of parameter settings You can manually set the date, time, and time zone or set the NTP server address. If NTP is enabled and Date & the device is connected to the Internet, the device Time Confguration List...
  • Page 16: Function Introduction Of Door Station

    10.8 Description of WiFi settings 11. Function Introductions of Door Station 11.1 Door Station Calls Indoor Monitor Users can turn WiFi on or off. When enabling WiFi, WiFi select the corresponding WiFi SSID and enter the When the visitor presses the call button on the Door Station to settings WiFi password.WiFi must be 2.4GHz.
  • Page 17 English, Chinese, Vietnamese, Indonesian and Thai. Door Station parameters will be reset to Reset to Factory Mode the factory defaults. The door station will read out the IP add- Prompt IP Address ress of the door station. Panasonic Corporation RP.000.ZC-SM.273 http://www.panasonic.com...

This manual is also suitable for:

Vl-sc3235wxVl-vc3535bxVl-mc3035bxVl-mc3035wx

Table of Contents