Advertisement
Quick Links
Advertisement
Related Manuals for Technologic Systems TS-2100
Summary of Contents for Technologic Systems TS-2100
- Page 1 TS-2100 User’s Manual...
- Page 2 Fountain Hills, AZ 85268 480-837-5200 FAX 837-5300 info@embeddedx86.com http://www.embeddedx86.com/ This revision of the manual is dated June 4, 2001 All modifications from previous versions are listed in the appendix. Copyright © 1998-2000 by Technologic Systems, Inc. All rights reserved. 06/04/2001...
- Page 3 Technologic Systems Limited Warranty Technologic Systems warrants this product to be free of defects in material and workmanship for a period of one year from date of purchase. During this warranty period Technologic Systems will repair or replace the defective unit in accordance with the following instructions: •...
- Page 4 APPENDIX D – SYSTEM I/O MAP ........................15 APPENDIX E - BIOS INTERRUPT FUNCTIONS ....................16 Int 15h / Function B000h - Technologic Systems BIOS information................16 Int 15h / Function B010h - LED Control ......................... 16 APPENDIX F - DIRECT CONTROL OF THE 386EX DIO PINS ................. 17 APPENDIX G - USING A 12.5 MHZ BAUD CLOCK ...................
- Page 5 BIOS modifications you may require. This manual is fairly short. This is because for the most part, the TS-2100 is a standard 80386 based PC compatible computer, and there are hundreds of books about writing software for the PC platform.
- Page 6 4.2 Flash There is a total of 1 MB of Flash memory on the TS-2100. The top 128 KB of Flash are reserved for the BIOS and DOS-ROM. During POST, they are copied from Flash into DRAM at addresses E0000h through FFFFFh for improved performance (a standard technique known as BIOS Shadowing).
- Page 7 4000 feet (1200 meters) via twisted pair cable. Half-duplex RS-485 requires one twisted pair plus a Ground connection. Full-duplex RS-485 and automatic trans- mitter enable for half-duplex are not supported on the TS-2100. If either of these features is required, they are supported by the TS-2200 EPC.
- Page 8 Or it controls JP header pin additional ports may be added via the PC/104 expansion 11, if 485 not installed bus. Technologic Systems currently offers a 2 serial / 1 Read Returns status of TX485EN parallel port card, and other manufacturers sell cards with up to four additional serial ports.
- Page 9 P1.3 DIO lines available to the user. RTS1 / P1.1 TX485EN Pin 3 is a Digital output that drives the TS-2100 LED. Pins 5,8,9,and DCD2 P1.2 10 are i386EX programmable I/O lines. Pin 6 is a fixed input that can Buffered LED be read (inverted polarity) at the COM2 Status Reg.
- Page 10 This signal is also available as a digital output on the JP header. When power is first supplied to the TS-2100, the board mounted LED is immediately turned on under hardware control. Once the processor begins execution, the LED is turned off, then flashed on and off again briefly.
- Page 11 Windows 9X for your development work, the HyperTerminal accessory works well. To download a file to the TS-2100 from your host PC, execute DL.BAT at the DOS command line on the TS-2100 (while using console-redirection from within your terminal emulator) and begin the transfer with your terminal emulator.
- Page 12 TS-2100 User’s Manual Technologic Systems When you are finished, turn off the TS-2100, remove the jumper, and turn it back on. Your program will now execute every time the TS-2100 is turned on. While Manufacturing Mode is in operation, the board LED provides feedback. While idle, the LED will cycle on and off at approximately 1/2 Hertz.
- Page 13 When we are prioritizing work on these updated resources, feedback from customers (and prospective customers) is the number one influence. If you have questions, comments, or concerns about your TS-2100 Embedded PC, please let us know. Details for contacting us are listed in the front of this manual.
- Page 14 TS-2100 User’s Manual Technologic Systems Appendix A - Board Diagram and Dimensions JP HEADER Power 32 Pin Socket A32 B32 0.200" 3.575" 3.775" Figure 4 - Board Diagram Figure 5 - Board Dimensions (standard PC/104 8-bit module dimensions) Appendix B – JP Jumper Block Table 4 lists all option jumpers and their functions.
- Page 15 (RAM) 00000h 00000 Figure 7 – TS-2100 Memory Map (Not to scale) Appendix D – System I/O Map The following table lists the I/O addresses used by the system. All other I/O locations from 100h through 3F7h are available on the PC/104 expansion bus.
- Page 16 E.g. If the current BIOS version is 1.25, the register will contain 19h (19h = 25 decimal). CH = Base Flash Memory Size / 512kB The TS-2100 is available with 1024kB of base Flash memory standard. This would be returned as 02h.
- Page 17 TS-2100 User’s Manual Technologic Systems Appendix F - Direct Control of the 386EX DIO Pins The Intel386 EX processor has three 8-bit bi-directional I/O ports, all of which are functionally identical (Figure 16-1). Each port has three control registers and a status register. All three ports share pins with internal peripherals.
- Page 18 TS-2100 User’s Manual Technologic Systems In the default configuration, P1.5, P1.0 and P3.6 are all initialized as inputs, while P3.0, P3.1, and P3.3 are initialized as "peripherals" (IRQ4, IRQ3, and IRQ5) Warning: When changing these registers, always use read/modify/write procedures so that other port pins (used by on-board peripherals) are not affected.
- Page 19 TS-2100 User’s Manual Technologic Systems Appendix I - Manual Revisions • 06/04/01 Updated board dimensions in Appendix A • 11/6/00 Updated System I/O Map • Updated URL to Intel 386EX User's Guide • 07/22/99 Added section 11.3 & Appendix F •...
Need help?
Do you have a question about the TS-2100 and is the answer not in the manual?
Questions and answers