Page 1
User Guide RP-BE58 RP-BE58 BE3600 Dual-Band WiFi Range BE3600 Dual-Band WiFi Range Extender Extender...
Page 2
Product warranty or service will not be extended if: (1) the product is repaired, modi ed or altered, unless such repair, modi cation of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing.
1.3 Your wireless range extender ........5 1.4 Positioning your wireless range extender ....7 Getting started 2.1 Set up RP-BE58 as a WiFi range extender ....8 A. via App ................8 B. via WPS ................9 2.2 Set up RP-BE58 as an AiMesh Node ......10 Tutorial AiMesh ................
Quick Start Guide Extender NOTES: • If any of the items are damaged or missing, contact ASUS for technical inquiries and support. Refer to Service and Support at the back of this user manual. • Keep the original packaging material in case you would need...
1.3 Your wireless range extender Power LED Refer to LED Explanations on the next page for details. WPS button This button launches the WPS Wizard. Reset button This button resets or restores the system to its factory default settings. LAN port Connect a network cable into this port to establish LAN connection.
Page 6
LED Explanations WiFi Range Extender Mode Status LED Behavior Booting up Blinking White Booting up complete (not connected to Router) Solid Blue Reset (use a pin to press the reset button for 5 seconds) Blinking Yellow Rescue mode Solid Purple Starting WPS Blinking Blue Connected to the router with Good Signal...
• Plug your RP-BE58 into a power outlet near you router/AP. • Check the LEDs and see the LED Explanations. • Wait for the LED to ash and turn solid blue, indicating that your RP-BE58 is ready to connect to your existing router/AP.
Use this product in environments with ambient WARNING! temperatures between 0°C (32°F) and 40°C (104°F). If you would like to connect RP-BE58 to other WiFi networks excluding AiMesh-supported routers, please download the ASUS Extender app or set up with the WPS button.
B. via WPS 1. Press the WPS button on your router/AP. 2. Press the WPS button on your RP-BE58 for more than two (2) seconds until the LED starts to blink blue.
2.2 Set up RP-BE58 as an AiMesh Node If you already have an AiMesh router and you are going to create an AiMesh system, please download and install ASUS Router app for RP-BE58 setup. 1. Download the ASUS Router app.
Page 11
4. Select RP-BE58 and follow the onscreen instructions to complete the setup. NOTE: Set up a password for your router to prevent unauthorized access.
Guest network How to set up a Guest Network? How to set up LAN IP? Operation mode How many AiMesh nodes are suggested in an AiMesh system? How to set up Access Point (AP) mode on an ASUS range extender device?
How to set up ASUS repeater with ASUS Extender app? How to set repeater mode on the ASUS wireless ranger extender (WebGUI)? How to use ASUS Device Discovery to nd the IP address of an ASUS router? How to nd the IP address of your wireless router or AP...
Page 14
How to set up WPS connection? Why does the WPS connection fail when using WPA3- Personal?
• Medical device interference: Maintain a minimum distance of at least 15 cm (6 inches) between implanted medical devices and ASUS products to reduce the risk of interference. • Kindly use ASUS products in good reception conditions to minimize the radiation's level.
Page 16
WARNING! • DO NOT place or drop objects on the top of the product. Avoid exposing the product to mechanical shock such as crushing, bending, puncturing or shredding. • DO NOT disassemble, open, microwave, incinerate, paint, or shove any foreign objects into this product. •...
Need help?
Do you have a question about the RP-BE58 and is the answer not in the manual?
Questions and answers