hyfire TAURUS Quick Start Manual

allation.
1
HYFIRE TAURUS SOUNDER VAD BASE (RED FLASH)
MOUNTING
BOX INSIDE THE BOX
ode • 1 x Sounder VAD Base
number
• Locate the mounting holes and mark them using a pencil
uct name • 2 x CR123A batteries
on the desired surface your are drilling.
• 2 x Screws
• Using a suitable-sized drill bit (6 mm) drill the marked
• 1 x Product manual
screw points on your chosen surface.
• 1 x Quick start guide
• Ensure you use the correct fixings for the type of surface
• 1 x QR code
you are mounting to.
• Screw the base to the ceiling using all fixing holes and
appropriate-sized screws.
IMPORTANT TO CONSIDER
3
When mounting a wireless device a comprehensive radio survey
should have been carried out to establish the location that provides
hensive radio survey
the best coverage and optimum reach. Taking into consideration the building
e location that provides
structure and materials, the survey identifies the wireless infrastructure
ng into consideration the building
required and product locations for optimum performance, identifying
s the wireless infrastructure
AND VOLUME
any factor that could prevent radio integrity.
performance, identifying
SELECTION
Avoid fixing or mounting the unit close to the following:
• Equipment that utilises large electrical currents
e following:
• Large metal objects or structures
rrents
• Fluorescent lighting fittings
• Metal ceiling structures
• IT cabling.
Keep 2 meters minimum spacing between other wireless equipment
• Put the sounder back onto the mounting base and secure
in the area to avoid signal interference.
with the two screws supplied.
ther wireless equipment
• Select the tone and volume you require (see next page)
• Ensure the programming switch in the base of the soudner EN54 approved environmental temperature range is -10°C to +55°C
is in position ON.
5
range is -10°C to +55°C
UNBOXING
• When unboxing the
B
• This comes with pre-formed mounting holes to mount the mounting base.
NT
• A securing screw is fitted to ensure unwanted removal of the attached device.
unit and its mounting base.
• Two screws are supplied to fix the sounder to the mounting base.
e mounting base.
• Dip switches are found inside the sounder to select your desired tone and volume.
the attached device.
ng base.
For more information, please refer to the complete product manual.
QUICK START GUIDE
HOLES
(Red Flash)
Sounder VAD Base (Red Flash)
TAU-BSB-23R-01
Hyfire Taurus
Sounder VAD Base (Red Flash)
FIXING
HOLES
IMPORTANT TO CONSIDER
TONE
When mounting a wireless device a compreh
should have been carried out to establish the
the best coverage and optimum reach. Takin
structure and materials, the survey identifies
required and product locations for optimum
any factor that could prevent radio integrity.
Avoid fixing or mounting the unit close to the
• Equipment that utilises large electrical cur
• Large metal objects or structures
• Fluorescent lighting fittings
• Metal ceiling structures
Sounder VAD Base
• IT cabling.
Keep 2 meters minimum spacing between ot
in the area to avoid signal interference.
TAU-BSB-23R-01
THE BOX
MOUNTING STEPS
QR code
TAU-BSB-23R-01
Proceed as follows to complete the device insta
Part number
Hyfire Taurus
Product name
Remove the mounting base from the sounder.
Remove the battery compartment cover on the base.
you will find the unit and its mounting base.
• Ensure switch on position.
• Fit the 2x CR123A batteries ensuring you have checked
• The LED will signal 4 times red.
• Move the switch in the base of the sounder base to position
HYFIRE TAURUS SOUN
INSIDE THE BOX
• 1 x Sounder VAD Base
(Red Flash)
• 2 x CR123A batteries
• 2 x Screws
• 1 x Product manual
• 1 x Quick start guide
• 1 x QR code
PROGRAMMING
SWITCH
BATTERY
COMPARTMENT
COVER
BATTERY A
LODGEMENT
they are the correct way round observing the polarity
indications on the base of the sounder base.
2
TAU-
THE B
QR co
QUICK
Part n
Produ
4
6
BATTERY
LODGEMEN
LED INDICATOR