Page 1
K-MINI ™ Use & Care Guide Get the most from your new Keurig brewer ®...
Page 2
D. K-Cup® Pod Assembly Housing E. Drip Tray Plate F. Drip Tray G. Water Reservoir Lid H. Water Reservoir I. Brew Button J. LED Indicator K. Power Button L. Power Cord M. Drip Tray Base For replacement parts, please visit www.Keurig.com...
Page 3
Before You Brew Plug & Power BREW Remove packing tape and cardboard from brewer and plug into a grounded outlet. Press the power button (note the power button will not illuminate). The add water indicator will flash blue.
Page 4
Fill & Place BREW Add 1 cup (8oz.) of water into a mug. Lift the water reservoir lid and pour the water into the reservoir. Lower the lid and place your mug on the drip tray base. NOTE: Do not add water to the reservoir if the brewer handle is up.
Page 5
Lift & Lower BREW The handle indicator will flash blue. Lift the handle. Water will drain from the water reservoir into the brewer. Once the water has fully drained, lower the handle. Do not insert a K-Cup® pod. NOTE: If you add more than 10 oz. of water, the excess water will drain into the drip tray.
Cleansing Brew Press the BREW button when it starts flashing blue. During the brew process, the BREW button will flash red to indicate that the water is heating. After about 2 2 Min minutes the BREW button will turn solid red when the water begins to dispense.
Page 7
Brew Your First Cup Fill & Place Add desired amount of water into a BREW mug (6oz. minimum, 10oz. maximum). Lift the water reservoir lid and pour the water into the reservoir. Lower the lid and place your mug on the drip tray base.
Page 8
Lift & Insert BREW The handle indicator will flash blue. Lift the handle. Water will drain from the water reservoir into the brewer. Once the water has fully drained, place a K-Cup® pod in the K-Cup® pod holder. Lower the handle completely to close the lid.
Page 9
Brew & Enjoy Press the BREW button when it starts flashing blue. During the brew process, the BREW button will flash red to indicate that 2 Min the water is heating. After about 2 minutes the BREW button will turn solid red when the beverage begins to dispense.
Page 10
Brewer Exterior Water Reservoir BREW It is normal over time for discoloration, Keep your Keurig® brewer looking its spotting, or staining to appear in best by cleaning the exterior from the water reservoir. Results will vary time to time. Just clean with a damp, depending on the mineral content of soapy, lint-free, non-abrasive cloth.
45 minutes for the descaling procedure. STEP 1: Descaling Solution Rinse Turn on your brewer. Pour one third (4.6oz.) of the Keurig® Descaling Solution into the water reservoir then add slightly less than 3/4 cups of fresh water. Place a large ceramic mug on the drip tray plate.
Page 12
NOTE: The cleaning action of Keurig® Descaling Solution may result in a “foam” dispensed from the brewer. This is natural, as the solution is reacting with the scale inside. For a brewer that is heavily scaled, the brewer may not fill properly after the descaler is added.
Page 13
Helpful Hints Water quality varies greatly. If you notice an undesirable taste in your beverage (such as chlorine or mineral tastes), we recommend using bottled or filtered water. Do not use distilled water. Service Beyond these recommended cleaning and maintenance procedures, this brewer is not user serviceable.
Page 14
Click or Call! Have Questions? We’re here to help. Visit support.Keurig.com for step-by-step videos on cleaning, descaling, and more. Still Need Help? Give us a call at 1-866-901-BREW (2739)
Page 15
K-Cup® Pod Holder To remove the K-Cup® pod holder from the brewer, lift the handle and grasp BREW the top of the K-Cup® pod holder with one hand while pushing up on the bottom of the K-Cup® pod holder from underneath with the other until it releases.
Page 16
Gently move it around to loosen any coffee grounds. Lower the handle completely and run two water-only brew cycles. Do not insert a K-Cup® pod. TIP: Refer to support.Keurig.com for video instructions on cleaning the entrance/exit needles.
Troubleshooting Grounds in Your Coffee Grounds may have gathered in the exit or entrance needles and can be cleaned using a straightened paper clip or similar tool. • Clean the Exit Needle of the K-Cup® pod holder. Refer to the exit needle care instructions.
Page 18
water reservoir into the brewer. If the light still does not flash, power off and place a mug on the drip tray. Hold down the BREW button and continue to hold down until all the water is dispensed into the mug. •...
It is recommended that you register your brewer on Keurig.com/new so that your purchase information will be stored in our system. Keurig will, at its option, repair or replace a defective brewer without charge upon its receipt of proof of the date of purchase.
Nor does this warranty cover damages caused by use of non-Keurig® pods or accessories, services performed by anyone other than Keurig or its authorized service providers, use of parts other than genuine Keurig® parts, or external causes such as abuse, misuse, inappropriate power supply, or acts of God.
Page 21
Fully experience the benefits that come with your new Keurig® brewer at KEURIG.COM NEW ✓ REGISTER DISCOVER your new Keurig® brewer your favorite coffees with our customized taste quiz and to activate your warranty and receive a special savings offer...
Need help?
Do you have a question about the K-MINI and is the answer not in the manual?
Questions and answers