PAC SRK-GM14HX Manual

Radio replacement kit for select 2014-2019 silverado/sierra trucks

Advertisement

Stinger HEIGH10
Introduction and Features
The SRK-GM14HX is a complete radio replacement kit for the installation of the Stinger HEIGH10 (UN1810) modular radio in
Chevrolet Silverado and GMC Sierra trucks. All modules, cables and adapters are included to retain important features of the
factory system, including: OnStar, front and rear park assist, warning chimes, factory reverse camera, steering wheel-mounted
radio controls and AM/FM reception. Plug & Play wiring harnesses allow for quick and easy installation without the need to cut or
splice any wiring. The display mounting panel allows flush mounting the 10 inch display without modifying/cutting any part of the
vehicle's sub-dash.
Important Notes
We recommend reading this manual thoroughly to familiarize yourself
with the entire process prior to beginning the installation.
1. Does not retain the following factory features:
● Factory satellite radio
● Rear seat entertainment system (RSE)
● Time of Day in Cluster
● Factory USB Ports
2. If installing aftermarket amplifiers, the included RPA-SPK can be used to retain OnStar/chimes.
3. Chime volume can be adjusted in the HEIGH10's settings
4. The Voice button can be set to activate the factory OnStar function when pressed for longer than 1.5 seconds or given the
ability to control the aftermarket radio. This option can be found in the Installer Settings on the HEIGH10. By default, this fea-
ture is set to control the aftermarket radio, but OnStar can still be accessed by using the mirror controls.
5. This guide is applicale to HEIGH10 (UN1810) radios. For ix210 (HORIZON10/HEIGH10+) radios, see the ix210 Installation
Guide
Recommended Tools
Plastic Panel Tool
7mm Socket
10mm Socket
Included Components
1. Display Mounting Panel
2. Dual USB Extension (SSUSB3)
3. AM / FM Antenna Adapter (BAA22)
4. Main Harness Adapter (SR-SRK-ADAPT-UN1810)
5. Main Harness (SRK-GM14HX-HAR)
6. Vehicle Harness Adapter (GM52-ADAPT)
7. Radio Replacement Interface (GM6A-SRK)
8. Steering Wheel Control Harness (GM5LIN-SW-HAR)
9. Factory Rear Camera Adapter (CAM-GM51-HAR)
10. IOB Display Harness (GM5CAM-DIS-HAR)
11. MOST Loops (MOST Loop 1 / MOST Loop 2)
12. External Chime Speaker (RPA-SPK)
13. Differential Video Adapter (RPA-VA1)
14. Satellite Antenna Adapter (SAT-01)
15. Side Mounting Brackets (L & R)
16. PAC-Link Cable (10P-2-10P-6)
17. PAC-Link Module (PL1)
NOTE: Along with the SRK-GM14HX components,
additional hardware and wire harnesses from the HEIGH10
(UN1810) kit will also be used in the installation.
®
Pacific Accessory Corporation
● Valet Mode
● Teen Driver Features
● OnStar Text
● Wi-Fi
Ratchet
Torx T15 Screwdriver
Small Flat-blade Screwdriver
© 2024 Stinger. All rights reserved. PAC is a Power Brand of Stinger Solutions.
Radio Replacement Kit for select
2014-2019 Silverado/Sierra Trucks
Pick Tool
Wire Feeder
Power Screwdriver
1
2
8
7
12
13
SRK-GM14HX
16
6
5
4
3
10
9
15
14
Rev: V1
Page 1
Date: 123024
17
11

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SRK-GM14HX and is the answer not in the manual?

Questions and answers

Summarization of Contents

Introduction and Features
Key Features Overview
Details the capabilities and retained factory system features of the SRK-GM14HX kit.
Important Installation Notes
Lists factory features not retained and critical pre-installation considerations for the kit.
Wiring Overview
SRK-GM14HX Main Harness Connections
Diagram showing main harness connections for the SRK-GM14HX kit.
Stinger ix210 Connections
Notes connections for the Stinger ix210 (Horizon10/HEIGH10+) radios.
Section 1: Disassembly
Center Dash Disassembly
Step-by-step instructions for removing the center dash trim and radio panel.
Center Dash Disassembly Continued
Further steps for removing connectors and the upper radio module from the dash.
Lower Storage Compartment Removal
Instructions for removing the lower storage compartment assembly.
Glove Box Removal (Optional)
Optional procedure for removing the glove box for specific vehicle configurations.
A Pillar Removal
Procedure for removing the passenger side A-pillar trim panel.
Lower Steering Column Cover Removal (Optional)
Optional procedure for removing the lower steering column cover.
Section 2: In-Vehicle Harness Connections and Preparation
Dual USB Extension (SSUSB3) Installation
Instructions for installing the SSUSB3 dual USB extension for the HEIGH10.
Factory Rear Camera Retention Harness (CAM-GM51-HAR)
Procedure to connect the rear camera retention harness at the HMI module.
Steering Wheel Control (SWC) Retention Harness (GM5LIN-SW-HAR)
Instructions for installing the SWC retention harness at the steering column.
GPS Antenna Installation
Steps for positioning and routing the GPS antenna for optimal reception.
Section 3: Interface and Main Harness Connections and Preparation
RP5-GM51 Radio Interface Connections
Detailed connection steps for the RP5-GM51 radio interface module.
Main Harness Connections (SR-GM14H-HAR-A)
Steps for connecting the main harness adapter and associated cables.
Section 4: Display Mounting Panel Preparation
Transferring Climate Controls
Instructions for transferring factory climate controls to the new mounting panel.
Mounting the Display
Procedure for physically mounting the HEIGH10 display to the prepared panel.
Section 5: Radio Module Preparation
Radio Module Side Brackets
Attaching side mounting brackets to the HEIGH10 radio module.
Section 6: Radio Unit Installation
Mounting the Radio Module
Steps for sliding and securing the HEIGH10 radio module into the vehicle.
In-Vehicle Harness and Cabling Connections
Detailed steps for connecting various harnesses and cables in the vehicle.
In-Vehicle Harness and Cabling Connections Continued
Completing the harness and cabling connections for radio unit installation.
Product Updates and Support
Firmware Updates (RadioPRO)
Information on updating the PAC GM6A-SRK interface firmware.
Firmware Updates (Stinger Radio & PAC APK)
Guide to updating HEIGH10 radio and PAC Application firmware.
RadioPRO LED Feedback Indicators
Explanation of LED status lights on the RadioPRO interface.
Technical Support Contact
Provides email and phone number for technical assistance.

Table of Contents