Related Manuals for aiko Neostar 2N A455-MAH54Mw
Summary of Contents for aiko Neostar 2N A455-MAH54Mw
- Page 1 AIKO PV Module Installation Manual Mono Glass Module Website: www.aikosolar.com Email: marketing@aikosolar.com AlKO Dual Glass Module Installation Manual, Version 12.1, Sep 2024...
-
Page 2: Table Of Contents
This Installation Manual provides information regarding the installation and safe use of PV Power Generation Modules (hereinafter referred to as “PV modules”）produced by Zhejiang Aiko Solar Technology Co., Ltd. (hereinafter referred to as “AIKO”). Installation and day to day maintenance of modules shall be in accordance 6.1 General requirements with all safety precautions specified in this Manual and local laws. -
Page 3: Overview
01/02 Overview / Laws and acts / General information Overview General information Thank you very much for choosing the products of Zhejiang Aiko Solar Technology Co., Ltd. (hereinafter referred to as “AIKO” ). Structural diagram of single-glass modules This Installation Manual contains important information regarding electrical and mechanical installation which you shall and component know before installing modules. -
Page 4: Wiring Method
03/04 General information Packing List 3.2 Wiring method Packaging List: Packaging list including the information of the PV module type, Module barcode information, number of modules, package weight, package dimension as well as cells color classification. To ensure consistency of the overall color of system when the customer use the The junction box of AlKO PV modules is located in the middle position. -
Page 5: General Safety
DC voltage greater than 50V or power greater than 240W that may be accessible to the public. Modules are desianed with safety Class ll and fire class rating C. Before to handle and install AIKO PV modules, read carefully and understand this Installation Manual. If you need any explanation, contact AIKO (aikosolar.com). -
Page 6: Fire Safety
If anything wrong is observed, please box or cables under any circumstances. Two or more people must hold the edges of the PV modules with both hands. contact AIKO logistics and sales staff immediately. Crane unloading: 4.3 Considerations for PV Module Storage and Placement... -
Page 7: Installation Conditions
When the surface of the module is perpendicular to sunlight, the output power reaches the maximum output value. AIKO recommend the installation angle should not less than 10°. occur at the connection between the PV module and the racking or at the ground connection. Anti-corrosive materials (e.g., stainless steel or aluminum materials) must be used in contact with PV modules and the mounting position must be... -
Page 8: Mechanical Installation
Other mounting configurations may be used provided that consultation is made with, and prior written consent is received from AIKO. Failure to do so will invalidate our warranty. Use appropriate corrosion-proof fastening materials. All mounting hardware (bolts, spring washers, flat washers, nuts）... - Page 9 Note: It is important to ensure the bolts do not fail due to deformation or corrosion during the over all load of the PV module.AIKO 1. The installation methods shown in the table above are based on experimental results, please contact AIKO for more recommend the thickness of washer should 1.7mm and use M8 and M6 bolt tightening torques must be within16~20Nm...
-
Page 10: Electrical Installation
The following formula may be used: Note: Maximum system voltage ≥ N×Voc×[1+β*(Tmin-25)] 1. The installation methods shown in the table above are based on experimental results, please contact AIKO for more details on other installation methods and load capacity not listed. Where: 2."/"identifies that there is no such installation. -
Page 11: Cables And Connections
90℃ and are UV resistant meeting local electrical installation standards at the location may be used for grounding AIKO PV modules. Grounding device shall be used as PV connecting lines. The minimum bending radius of the cable is 43mm. -
Page 12: Maintenance Of Pv Modules
PV modules shall be inspected and maintained on a regular basis, especially within the warranty period, which is an obligatory responsibility of the user. Any damage or other visible abnormalities of the PVmodule shall be reported to AIKO customer service(cs@aikosolar.com) upon discovery. -
Page 13: Visual Checks Of The Modules
Whether the connectors are properly sealed and the cables are properly fastened Whether the sealant of the junction box is cracked 9.4 AIKO Technical Support In order to request Technical Support: Collect evidences of the issue as (a) photos and (b) measurements.
Need help?
Do you have a question about the Neostar 2N A455-MAH54Mw and is the answer not in the manual?
Questions and answers