Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for TW SOLAR TWMND-54HB430
Summary of Contents for TW SOLAR TWMND-54HB430
- Page 1 Monofacial Module Installation Manual for Tongwei Solar (Hefei) Co., Ltd...
- Page 2 PV Module Installation Manual Monofacial Module Installation Manual for 182-78/182-72-TOPCON/182-54-TOPCON/210-66-PERC Serial number：TWsolar-M-RD-TS002 Version number：A0 2023-06-05 Published 2023-06-05 Implemented Tongwei Solar (Hefei) Co., Ltd...
- Page 3 PV Module Installation Manual Monofacial Module： Max. System Voltage: up to 1500VDC (Voc at STC) With ½ cut of 182 mono c-Si cell-- single glass: TWMND-78HS605 TWMND-78HS610 TWMND-78HS615 TWMND-78HS620 TWMND-78HS625 TWMPD-78HS590 TWMPD-78HS595 TWMPD-78HS600 TWMPD-78HS605 TWMPD-78HS610 TWMPD-78HS615 TWMND-72HS565 TWMND-72HS570 TWMND-72HS575 TWMND-72HS580...
- Page 4 With ½ cut of 210 mono c-Si cell-- single glass: TWMPF-66HS660 TWMPF-66HS665 TWMPF-66HS670 TWMPF-60HS600 TWMPF-60HS605 TWMPF-60HS610 The modules mentioned in this installation manual are only allowed to be installed below 2000m above sea level. Meaning of crossed-out wheeled dustbin: Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
-
Page 5: Table Of Contents
CONTENTS Purpose of this Manual ......................04 Disclaimer ..........................04 Safety & Transport ........................05 Mechanical Installation ......................10 Electrical Installation ........................15 Grounding ..........................17 Bypass Diodes and Block Diodes .....................18 Maintenance ..........................19 Tongwei Solar (Hefei) Co., Ltd... -
Page 6: Purpose Of This Manual
This manual applies exclusively to the solar photovoltaic module (here in after referred to as Module) of TW solar energy Co., Ltd. (here in after referred to as TW). The contents of this manual involve the installation methods, operation safety and maintenance information of TW’s Modules. -
Page 7: Safety & Transport
SAFETY & TRANSPORT General Detailed Rules Keep all the Modules and electrical connectors clean and dry before installation. Use both hands to carry Modules. Do not overlap Modules. Be cautious when carrying Modules. Slip-proof gloves are necessary. ... - Page 8 SAFETY & TRANSPORT Electrical Performance Safety PV modules can produce DC current under sunlight. Any contact of exposed metal at module's wiring parts may result in electrical shock or burn. Any contact of 30V or larger DC Voltage can be fatal. ...
- Page 9 SAFETY & TRANSPORT Description of Package Signs Before the operation, it is necessary to read carefully the unpacking instruction and outer packing box instruction, and carry out the operation as instructed. 1. DO NOT expose the module to rain or 2.
- Page 10 SAFETY & TRANSPORT Unloading, Transportation and Storage When the Modules are delivered to the project site, the freight car shall be ready in the flat, even and open area for parking and unloading. Forklift unloading: Choose the appropriate carrying forklift according to the commodity weight, unload the Modules from the freight car and place them on flat ground.
- Page 11 SAFETY & TRANSPORT Storage in the project site warehouse: Storage environment requirements: Humidity＜85%, temperature -20 ~+50℃; Modules statically stacked for ≤2 layers. Temporary storage at the project site: The Modules shall be stored in a dry, well-ventilated place. They shall not be stacked but shall be covered with waterproof cloth to prevent dampness in the Modules.
-
Page 12: Mechanical Installation
MECHANICAL INSTALLATION Location Selection Select suitable places to install Modules. The module in the north latitude region shall face south, and shall face north in the south latitude region. Install Modules at the places with sufficient sunlight and without shade at any time. If a module is shaded or even partially shaded, it will result in lower power output. - Page 13 MECHANICAL INSTALLATION Installation requirements Ensure the module installation method and support system sufficiently robust, so that the Modules can undertake the preset loading conditions, the support installer or supplier shall provide necessary guarantee and other related certifications. The installation support system shall pass the inspection and test by the third-party test institution with the static mechanic analysis capability, and use the local national or international standards, such as DIN1055 or equivalent.
- Page 14 MECHANICAL INSTALLATION Framed Modules Installation with the mounting clamp Table 1 Installation Method Installation Method A Installation Method B Clamping on the long side Note: The length of the clamp≥50mm.
- Page 15 TWMND-54HS420 TWMND-54HS425 TWMND-54HS430 TWMND-54HS435 TWMND-54HS440 1722*1134*30 3600/1600 3600/1600 TWMND-54HB415 TWMND-54HB420 A/4±50 TWMND-54HB425 TWMND-54HB430 TWMND-72HS565 TWMND-72HS570 2278*1134*35 3600/1600 3600/1600 TWMND-72HS575 TWMND-72HS580 TWMND-78HS605 TWMND-78HS610 A/8±50 3A/8±50 TWMND-78HS615 TWMND-78HS620 TWMND-78HS625 TWMPD-78HS590 2465*1134*35 3600/1600 TWMPD-78HS595 TWMPD-78HS600 TWMPD-78HS605 TWMPD-78HS610 TWMPD-78HS615 TWMPF-60HS600 TWMPF-60HS605 2172*1303*35 3600/1600 360～420...
- Page 16 MECHANICAL INSTALLATION The Modules may be installed and fixed with the following methods: Clamping system: use proper clamp, and fix the module with the installation support, as shown in Fig. 3. The clamp must maintain an overlap of unless 8 mm with the frame of the module(you can change the cross section of the clamp if the module is securely installed).
-
Page 17: Electrical Installation
ELECTRICAL INSTALLATION DC power generated by the photovoltaic system can be converted into AC power and fed into the grid. Policies on connecting renewable energy system to the grid vary from region to region. Consult senior system designer before designing the system. Generally, the system installation shall be formally approved by the local public sector. - Page 18 ELECTRICAL INSTALLATION Figure 4 Connection in Series Figure 5 Connection in parallel Refer to the local regulations to determine the system wire size, types and temperatures. The cross section of the cables and the capacity of the connectors must be selected to suit the maximum system short circuit current (The recommended section area for a single piece of Module is 4 mm , and the recommended rated current for the connector is greater...
-
Page 19: Grounding
GROUNDING Grounding by cable The grounding bolts must be made of stainless steel and be used in the specified grounding holes. First, make the M3.5 stainless steel bolt pass through the spring washer, flat washer, cup washer (copper conductor with a diameter of 2.1 mm) and star washer, and then insert through the grounding hole, flat washer and spring washer on the frame. -
Page 20: Bypass Diodes And Block Diodes
BYPASS DIODES AND BLOCK DIODES In a system with two or more Modules connected in series, if part of a Module is shaded while the other part is exposed to the sun, a very high reverse current will go through the cells which have been partly or entirely covered and it will cause overheat on the cells, which may damage the Module. -
Page 21: Maintenance
MAINTENANCE Normally, the Modules do not need repair. Follow the maintenance methods below to ensure the best performance of the Modules: In most conditions, the normal rainwater can keep the module glass clean. Clean the glass surfaces with wet soft sponge or cloth if necessary. Use mild non-abrasive cleaning agent to remove stubborn dirt.
Need help?
Do you have a question about the TWMND-54HB430 and is the answer not in the manual?
Questions and answers