Related Manuals for Schartec Prime 1000-Speed
Summarization of Contents
Important Safety Instructions
Intended Use
Defines the proper use of the garage door opener for private, non-commercial operations in dry rooms.
Unintended Use
Specifies prohibited uses like commercial sector or doors without fall protection.
Fitter and Installer Qualifications
Emphasizes installation and maintenance by competent persons as defined by EN 12635.
Installation and Repair Safety
Warns about high tension springs and mains voltage risks, requiring qualified personnel.
General Safety Warnings
Fastening Materials and Rope Hazards
Advises on using correct materials and removing pull ropes to prevent hazards.
Door Movement and Mounting Safety
Discusses risks of unintentional door movement and safety advice for mounting.
Boom Rail Mounting and Pinching Risks
Warns about pinching fingers during boom rail assembly and operation.
Commissioning and Operation Safety
Operational Risks and Precautions
Highlights risks of pinching, pull cord hazards, and rapid door closing.
Pull Cord and Rapid Closing Dangers
Warns against improper pull cord use and risks associated with faulty door springs.
Operational Safety and Precautions
Door Movement and Remote Control Safety
Advises keeping clear of door movement and safe remote control usage.
Safety Device Integrity and Testing
Emphasizes testing safety devices like photocells and seeking expert help if they fail.
Inspection and Maintenance
Maintenance Recommendations
Recommends expert inspection and monthly user checks for the opener.
Warranty Conditions
Warranty Exclusions and Duration
Details warranty coverage, exclusions, and duration periods.
Warranty Conditions and Performance
Outlines warranty applicability and covers material/manufacturing defects.
Product Description and Features
Safety and Performance Features
Highlights features like automatic safety reverse, soft start/stop, and self-learning capabilities.
Convenience and Control Features
Covers auto-close, LED, For-Link, partial opening, and remote control features.
Connectivity and Physical Design
Details accessory terminals, low headroom design, and button controls.
Pre-Installation Recommendations
Door and System Check
Crucial checks on door balance, springs, and overall condition before installation.
Required Clearance
Specifies minimum 30mm clearance between the door's highest point and the ceiling.
Emergency Release Requirement
Advises on the necessity of an emergency release for garages without a second entrance.
Package Contents
Package Overview
Lists all components included in the opener package for installation.
Hardware Components
Details various screws, brackets, and accessories provided for mounting.
Installation Instructions
Boom Rail Assembly
Step-by-step guide for assembling the boom rail, including 2-part and 3-part configurations.
Mounting Brackets
Wall Bracket Mounting
Details on locating and mounting the wall bracket based on door width and wall position.
Door Bracket Mounting
Guidance on attaching the door bracket to a structural part of the door.
Installing Boom Rail and Opener
Attach Opener to Rail
Connects the opener to the boom rail using a sleeve and fasteners.
Mount Rail to Wall Bracket
Attaches the boom rail and opener assembly to the wall bracket.
Secure Boom to Ceiling
Explains how to mount the boom to the ceiling using Easy-Click brackets.
Position Opener Level
Lifts and supports the opener to ensure it is level and centrally positioned.
Final Installation Steps
Attach Ceiling Hangers
Secures the boom rail to ceiling-mounted extension pieces.
Attach Door Arms
Connects the trolley to the garage door using straight and curved arm pieces.
Lock Trolley into Belt
Lifts the door to engage the trolley with the drive belt, preparing for programming.
Display Menu Operation
Operating Feature Settings
Guides through entering programming mode and navigating feature settings.
Using Display Buttons
Explains the function of each button (SET, CODE, UP, DOWN) for various operations.
Programming Instructions
Programming Opening and Closing Limits
Details the process of teaching the opener the full open and closed positions.
Programming Remote Controls
Instructions for pairing remote controls with the garage door opener.
Deleting Stored Remote Controls
Procedure to erase all programmed remote control codes from the opener.
Obstruction Force Adjustment
Force Adjustment Procedure
Explains how to adjust the force the opener applies before reversing or stopping.
Travel Speed Setting
Adjusting Travel Speed
Guides on adjusting the opening and closing speed of the garage door opener.
Automatic Closing
Automatic Closing Setup
Details how to configure the automatic closing feature, requiring a photocell.
Automatic Closing Conditions
Setting Auto-Close Conditions
Defines conditions for auto-close operation, such as door position.
LED Function
LED Light Delay Adjustment
Explains how to set the delay time for the courtesy LED light.
Reversal Height Setting
Adjusting Reversal Height
Adjusts the height at which the opener reverses upon encountering an obstacle.
Partial Opening Setting
Configuring Partial Opening
Configures a partial opening for ventilation purposes using a remote button.
Remote Control Button Function
Remote Button Operation Modes
Sets whether all remote buttons control the opener or individual buttons control specific functions.
Remote Control Storage
Adjusting Remote Storage Quantity
Adjusts the maximum number of remote controls that can be stored by the opener.
Reversal Limit Setting
Setting Reversal Limit Distance
Sets the ground clearance the opener ignores before reversing during closing.
Wicket Door Contact Setting
Configuring Wicket Door Contact
Configures the contact setting for a wicket door (Normally Open or Normally Closed).
Photocell Setting
Enabling/Disabling Photocell
Enables or disables the photocell function, essential for automatic closing and safety.
Maintenance Alarm Setting
Setting Maintenance Alarm Cycles
Configures a maintenance alarm based on the number of door cycles.
External Control and Accessory Connections
O/S/C Button Connection
Details connecting O/S/C buttons (key-switch, push-buttons) for door operation.
Photocell Connection
Explains how to connect a photocell for enhanced safety.
Flashing Light Connection
Describes connecting a flashing light for visual signaling.
Wicket Door Connection
Explains the function ensuring the main door opens only when the wicket door is closed.
Manual Disengagement
Attaching Warning Label
Instructs to attach a warning label about entrapment risk near controls.
Manual Release Operation
Details how to disengage the trolley for manual door operation and re-engage it.
Technical Specifications (Standard Models)
Prime 600, 1000, 1200 Specs
Lists technical data like pull force, door area, weight, and speed for different models.
Technical Specifications (Speed Models)
Prime 600-Speed, 1000-Speed Specs
Provides technical details for speed models, including opening/closing speed.
Parts Listing
Parts Identification and Quantities
A list and diagram of all parts included in the opener package.
Common Faults and Solutions
Troubleshooting Guide
Provides solutions for common issues like no power or incorrect stopping.
Common Faults and Solutions (Continued)
Troubleshooting Common Issues
Offers solutions for LED issues, remote control problems, and stored codes.
Boom Rail Shortening Instructions
Boom Rail Shortening Procedure
Step-by-step guide on how to safely shorten the boom rail and drive chain/belt.
Need help?
Do you have a question about the Prime 1000-Speed and is the answer not in the manual?
Questions and answers