Omron E3AS-HL500MN M3 Instruction Sheet

E3AS-HL150□/HL500□
Model
CMOS Laser Sensor
INSTRUCTION SHEET
Thank you for selecting OMRON product. This sheet primarily describes precautions
required in installing and operating the product.
Before operating the product, read the sheet thoroughly to acquire sufficient
knowledge of the product. For your convenience, keep the sheet at your disposal.
TRACEABILITY INFORMATION:
Importer in EU:
Manufacturer:
Omron Europe B.V.
Omron Corporation,
Wegalaan 67-69
Shiokoji Horikawa, Shimogyo-ku,
NL-2132 JD Hoofddorp,
Kyoto 600-8530 JAPAN
The Netherlands
The following notice applies only to products that carry the CE mark.
Notice:
In a residential environment, this product may cause radio interference,
in which case the user may be required to take adequate measures.
© OMRON Corporation 2020 All Rights Reserved.
PRECAUTIONS ON SAFETY
●Meaning of Signal Words
Indicates a potentially hazardous situation which, if not avoided,
WARNING
will result in minor or moderate injury, or may result in serious injury
or death. Additionally there may be significant property damage.
Indicates a potentially hazardous situation which, if not avoided,
CAUTION
may result in minor or moderate injury or in property damage.
WARNING
This product is not designed or rated for ensuring safety of persons
either directly or indirectly. Do not use it for such purpose.
Do not use the product with voltage in excess of the rated voltage.
Excess voltage may result in malfunction or fire.
CAUTION
Its component may be damaged and/or degree of protection may be degraded.
Please do not apply high pressure water intensively at one place during cleaning.
To safely use laser products
WARNING
Looking into the Outgoing light continuously may cause visual impairment.
Do not look directly into the Outgoing light.
Caution-Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation exposure
Attention-Lʼutilisation des commandes ou réglages ou lʼexécution des
procédures autres que celles spécifiées dans les présentes exigences
peuvent étre la cause dʼune exposition à un rayonnement dangereux
Do not disassemble this product.Doing so may cause exposure to
the built-in light source which can damage eyes and skin. Never
disassemble it.
Laser safety measures for laser equipment are stipulated by the country of use. Follow
the instructions described below categorized in four cases.
・ Usage in Japan
The JIS C6802:2014 standard stipulates the safety precautions that users must take
according to the class of the laser product. This product is classified into class 1 defined
by this standard.
・ Usage in U.S.
This product is subjected to the U.S. FDA (Food and Drug Administration) laser
regulations. This product is classified into Class 1 by the IEC 60825-1:2014 standard
according to the regulations of Laser Notice No.56 of the FDA standard. This product is
already reported to CDRH (Center for Devices and Radiological Health).
Accession Number: 1920014-001
When using a device equipped with the product in the U.S., attach an FDA certification
label near the sensor mounted on customer equipment.
FDA certification label
・ Usage in China
This product is classified into Class 2 by the GB7247.1:2012(IEC60825-1:2007) standard.
When using a device equipped with the product in China, attach a Warning label near
the sensor mounted on customer equipment.
Warning label
Center of laser projection
・ Usage in countries other than U.S. and China
This product is classified into Class 1 by the IEC60825-1:2014/EN60825-1:2014+A11:2021
standard.
* 5 6 3 0 5 3 9 - 9 D *
1
Precautions for Safe Use
Please observe the following precautions for safe use of the products.
•Do not reverse connection of DC power supply polarity. Do not connect
to AC power supply.
•Do not short-circuit the load.
•Never use this product with AC power supply. Otherwise it may
explode.
•The maximum power supply voltage is 30 VDC. Before turning on the
product's power, make sure that the supply voltage does not exceed
the maximum power supply voltage.
•Do not use the product in environments where flammable or explosive
gases are present.
•Please assess the safety beforehand when using the product in
chemicals and/or oil environments.
•Do not remodel the product.
•Do not touch the metal surface with your bare hands when the
temperature is low. Touching the surface may result in a cold burn.
•Burn injury may occur. The product surface temperature rises
depending on application conditions, such as the ambient temperature
and the power supply voltage. Attention must be paid during
operation or cleaning.
Precautions for Correct Use
•Do not hit the product using a hammer for installation.
•The product must be installed with the specified torque or less.
For M8 connector and Pre-wired M8 connector, the proper tightening
torque is from 0.3 to 0.4 N ・ m.
In case of M12 Pre-wired smartclick connector, manually tighten the
connector.
•Tightening torque for the mounting hole is 0.6 N ・ m or less (M3 screw).
•Do not use the product in ambient atmosphere or environment exceeding
the rating.
•Output pulses may be generated when the power is turned off. It is
recommended to turn off the power of the load or load line first.
•The extension of the cord under the standard I/O mode should be 100 m
or less.Under the IO-Link mode, the length should be 20 m or less.
•Do not pull the cord too strongly.
•Be sure to turn off the power supply when connecting or disconnecting
the cable.
•Wait for at least 600 ms after turning on the product's power.
•The product is rated as IP67 but please avoid using the product
underwater, under rain, and outdoors.
•If the Sensor wiring is placed in the same conduits or ducts as high-voltage
or high-power lines, inductive noise may cause malfunction or damage.
Wire the cables separately or use a shielded cable.
•Do not use the product in direct sunlight.
•Do not use the product where humidity is high and dew condensation
may occur.
•Do not use the product where corrosive gases may exist.
•Use a key lock to prevent malfunction if high-pressure wash water or other
substances come into contact with the button.
• Do not apply high-pressure washing water directly to the sensor's light
emitting / receiving surface from a short distance. As the antifouling
feature may be impaired, keep a sufficient distance from the light emitting
/ receiving surface.
•Do not use the product at a location subject to shock or vibration.
•To use a commercially available switching regulator, FG (frame ground)
must be grounded.
•This product cannot be used as a detection device for human body
protection.
•Do not use organic solvents (e.g. paint thinner and alcohol) for cleaning.
Otherwise optical properties and protective structure may deteriorate.
•Be sure to check the influence caused by surrounding environments such
as background objects and/or LED lighting before using the product.
•Do not exceed 100,000 writing operations of the EEPROM (non-volatile
memory). Setting information is written to the EEPROM when a threshold
value change, teaching, or zero reset is executed.
Dispose in accordance with applicable regulations.
Package contents
Instruction sheet （this sheet） , Compliance sheet, Index list (attached for
IO-Link type only), FDA certification label, Warning label