Program Play - Yamaha GX-500RDS Owner's Manual

1 2 3
DISC DISC DISC
PTY SELECT PRESET/ TUNING/ BAND
YMERSION B.BOOST MUSIC
FREQ PS/PTY/RT/CT
MODE DOLBY NR REC/PAUSE
DIRECTION
1 1 2 3
1 2 3
6 7 8
6 7 8
A B C
TIME
TIME PROG R. TIME
MODE REPEAT RANDOM
2 DISC SKIP
TUNER
REC/PAUSE
Display information during programming
Play order
TRACK
K K
VCD PBC TUNER
TIMER
CD
AM
SLEEP
MD
C HALL
NOR TEST
YMERSION TAPE
PHANTOM
Selected track number
TRACK
K K
TOTAL
VCD PBC TUNER
TIMER
CD
AM
SLEEP
MD
C HALL
NOR TEST
YMERSION TAPE
PHANTOM
DISC CHANGE OPEN / CLOSE
A/B/C/D/E
5
VOLUME
DOWN UP
INPUT INPUT
MODE–PTY SEEK– START
RANDOM REPEAT TIME
TIME
HOUR MIN
AUTO/MANUAL MEMORY DISPLAY
TIMER TIME ADJ
STANDBY/ON
4 5
4 5
3
PRESET
9 0
D E
+
EDIT I0
TUNER
5
CD
Selected disc
RANDOM
1 2 3 4 5 6
EDIT
S F REP
7 8 9 10 11 12
A B VOLUME
PROG
13 14 15 OVER 15
Music calendar
Total playing time
RANDOM
1 2 3 4 5 6
EDIT
S F REP
7 8 9 10 11 12
A B
VOLUME
PROG
13 14 15 OVER 15
Compact disc player operation

Program play

You can program up to 20 tracks in any desired order.
1
When the CD player is stopped, press PROG to prepare for
programming.
9
* "PROG" ( ) and "P-01" (
and all track numbers on the selected disc (
begin flashing.
2
If necessary, select the desired disc by pressing DISC
SKIP.
* Just after you change the disc, the CD player reads the
contents of the newly selected disc for a few seconds.
During this internal operation, if you go on to the next
2
step, "WAIT" ( ) appears on the display and your
operation is canceled.
3
Use the numeric buttons to select the desired
track number.
* The selected track number (
of the programmed tracks (
display, and soon it will be replaced by the display of the
2
next play order ( ). Programmed track numbers on the
selected disc will stop flashing and light up on the music
7
calendar ( ).
* Pressing TIME displays the total play time of the
2
programmed tracks (
is replaced by the display of the next play order (
4
Repeat steps 2 and 3 to program other tracks.
5
/
Press to start the program play.
Notes
The total time of the programmed tracks will not be
displayed, if track number 16 or higher is programmed.
Skip ( / ) can be performed during play, but only
within the range of the programmed tracks.
Search ( / ) can be performed during play to search
all tracks, including unprogrammed tracks.
To cancel a programmed sequence
There are several methods as described below.
Press while the CD player is stopped.
Open the disc tray.
Turn this system into the standby mode.
To check (and correct) program data
1. Press PROG when the CD player is stopped.
2. Every time is pressed, the track numbers and
sequential order of the programmed tracks can be checked
one after another. The display of the track number can be
returned (sequentially in reverse order) by pressing
3. If you want to correct the program data, press a numeric
button to select the track to replace the one displayed. The
previously programmed track will be cleared from the
memory and the new one will be programmed.
To complete the correction, press PROG or
again.
2
) will light up on the display,
7
) will
1
) and the total play time
2
) will light up on the
) for about 1 second, and then it
2
).
/
once
.
E-11