Table of Contents
Advertisement
OPERATING FIREPLACE
FOR YOUR SAFETY READ
BEFORE LIGHTING
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing prop-
erty damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone
in your building.
• Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by hand,
don't try to repair it, call a qualified service technician. Force
or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
LIGHTING
INSTRUCTIONS
NOTICE: During initial operation of new heater, burn-
ing logs will give off a paper-burning smell. Orange
flame will also be present. Open damper or window to
vent smell. This will only last a few hours.
1. STOP! Read the safety information, above.
2. Turn off all electric power to the appliance.
3. Turn wall switch to the OFF position.
4. Open lower louver panel.
5. Turn equipment shutoff valve clockwise
position (see Figure 48). Do not force.
6. Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP! Fol-
low "B" in the safety information above. If you don't smell
gas, go to the next step.
7. Turn equipment shutoff valve counterclockwise
to the ON position. Do not force.
8. Close lower louver panel.
9. Turn on all electric power to the appliance.
10. Turn the wall switch to the ON position.
For more information, visit www.desatech.com
For more information, visit www.desatech.com
111251-01B
11. Visually locate the pilot. The ignitor should begin to
spark and the main burner should ignite once flame ap-
pears at pilot.
• If lighting the appliance for the first time each season, it
• If the appliance will not stay lit after several attempts,
Figure 48 - Turning Equipment Shutoff Valve to the OFF Position
1. Turn off the wall switch.
2. Turn off all electric power to the appliance if service is to
be performed.
3. Open lower louver panel.
4. Turn equipment shutoff valve clockwise
Do not force.
5. Close lower louver panel.
Figure 49 - Pilot
to the OFF
Clockwise
Note: The WRC receiver and hand-held remote control kit
must be purchased separately (see Accessories, page 37). Follow
installation instructions on page 24.
1. Turn equipment shutoff valve to ON position. You can now turn
the burner on and off with the hand-held remote control unit.
IMPORTANT: Be sure to press the ON/OFF buttons on the
C-clockwise
hand-held remote control unit for up to 3 seconds to assure
proper operation.
2. Press the ON/OFF button to turn the burner on and off.
OPERATING FIREPLACE
For Your Safety Read Before Lighting
Lighting Instructions
To Turn Off Gas To Appliance
Optional Remote Operation
may take several attempts before the supply gas can reach
the pilot and main burners.
follow the instructions To Turn Off Gas To Appliance,
below, and call your service technician or gas supplier.
Equipment Shutoff Valve
TO TURN OFF GAS
TO APPLIANCE
Pilot Burner
OPTIONAL REMOTE
OPERATION
25
25
Pilot Adjustment Screw
to OFF.
Clockwise
Sensing Rod
Ignitor
Advertisement
Table of Contents
