Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for BAUMAN 640P
Summary of Contents for BAUMAN 640P
- Page 1 BAUMAN MANUFACTURING 640H/640P DROP SPREADERS OPERATOR’S MANUAL...
- Page 2 MODEL: SERIAL NUMBER: PURCHASE DATE: DEALER/WHERE PURCHASED: DOCUMENT REVISION: NOVEMBER 2018 3 INDUSTRIAL DRIVE ELMIRA, ON N3B 2S1 PHONE: (519)669-4333 FAX: (519)669-2431 WWW.BAUMANMFG.COM...
-
Page 3: Table Of Contents
ATTACHMENT OF THE MACHINE ............................6 SPREADING MATERIAL ................................7 HYDRAULIC ROUTING INSTRUCTIONS ............................ 7 640H/640P PARTS LIST ................................8 640H, HYDRAULIC SPECIFIC PARTS LIST ..........................9 640P, PTO SPECIFIC PARTS LIST .............................. 9 INSTALLATION LOCATIONS ..............................10 OPTIONAL ATTACHMENTS ..............................16... -
Page 4: Introduction
The Bauman Drop Spreader is capable of spreading sand, salt, grit, or similar materials and should only be used for this purpose. Correct usage of the machine also includes following the factory’s preparation, operation and maintenance instructions. -
Page 5: General Information
GENERAL INFORMATION The operator must read and understand the information in this manual to ensure the correct service and operation of the machine and avoid unnecessary risk of accidents and breakdowns. Please Note: Stop the tractor engine before you adjust, lubricate, or repair the machine. Remember to remove the ignition key to make sure no one starts the tractor while you are repairing the machine. -
Page 6: Safety Instructions
This concerns your safety. The Bauman Drop Spreader should only be operated by one person. The operator should ensure that no one is close to the area where the machine is in use. Do not let others operate the machine unless you are certain that they have the necessary knowledge to operate the machine safely and correctly. -
Page 7: Safety Labels
Bauman Drop Spreader. SAFETY LABELS The danger labels on Bauman Manufacturing equipment are for the safety of the operator as well as pedestrians and bystanders. Read and obey warning and danger labels. The operator must ensure that before operating the machine, all guards and grills are in place and that they are attached properly. -
Page 8: Maintenance
MAINTENANCE Warning: When repairing, maintaining and cleaning the machine, it is particularly important to be aware of the safety precautions. Park the tractor (if connected) as a precautionary measure and disconnect power when servicing. Do not clean, lubricate or adjust the machine before the tractor engine has been stopped and the parking brake is activated. -
Page 9: Spreading Material
SPREADING MATERIAL REGULATING SPREAD QUANTITY The spreading quantity is adjusted with the tension adjustment lever. Correct adjustment is important. If the adjustment is too tight, unnecessary wear of the rubber belts or rotating parts may occur. If the adjustment is too slack, distribution of material will be uneven. Hydraulic Units: All hydraulic units are equipped with hydraulic flow control. -
Page 10: 640H/640P Parts List
640H/640P PARTS LIST ITEM PART NUMBER DESCRIPTION QTY. QTY. 1140 SB50-4 RUBBER FLAP FINGER BAR 40 1140 SB60-4 RUBBER FLAP DISTRIBUTOR DRUM 40 640 200 GRILL - HOPPER 1140 800 HOOK BRACKET 40B30 100 #40-30 TOOTH 1" BORE AP SMV 102... -
Page 11: 640H, Hydraulic Specific Parts List
640H, HYDRAULIC SPECIFIC PARTS LIST ITEM PART NUMBER DESCRIPTION QTY. QTY. 1140 900 HYD HOSE CLAMP HYD FLOW FLOW CONTROL VALVE 8GPM SEE BOM HYD KIT FLOW, HOSES AND FITTINGS 31.1 HYD6602-6-6-6 SWIVEL NUT RUN TEE - MJIC x MJIC x FJIC 31.2... -
Page 12: Installation Locations
INSTALLATION LOCATIONS CONNECTION SIDE, PTO CONNECTION SIDE, HYDRAULICS... -
Page 18: Optional Attachments
6” Extension adds 2-1/2 cu.ft. Part Number: 640 EXT 12” Extension adds 5 cu.ft. Part Number: 640 EXT-12 CUSTOM MOUNTING BRACKETS Contact Bauman Manufacturing to find a suitable mounting bracket. (Multihog mounting bracket shown) 3 POINT HITCH QUICK ATTACHMENT Part Number: BRACKET 3PT SSL... -
Page 19: Warranty Information
Bauman Manufacturing has been advised of the possibility of such damages. Except as provided herein, Bauman Manufacturing makes no warranties, expressed or implied, including without limitation, the implied warranties of merchantability and fitness for a particular purpose, with respect to the components.
Need help?
Do you have a question about the 640P and is the answer not in the manual?
Questions and answers