Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for BAUMAN 1040B
Summary of Contents for BAUMAN 1040B
- Page 1 BAUMAN MANUFACTURING 1040B DROP SPREADER OPERATOR’S MANUAL...
- Page 2 MODEL: SERIAL NUMBER: PURCHASE DATE: DEALER/WHERE PURCHASED: DOCUMENT REVISION: AUGUST 2020 3 INDUSTRIAL DRIVE ELMIRA, ON N3B 2S1 PHONE: (519)669-4333 FAX: (519)669-2431 WWW.BAUMANMFG.COM...
-
Page 3: Table Of Contents
Contents INTRODUCTION ..................................2 GENERAL INFORMATION ................................ 3 SAFETY INSTRUCTIONS ................................4 SAFETY LABELS ..................................5 MAINTENANCE ..................................6 ATTACHMENT OF THE MACHINE ............................6 SPREADING MATERIAL ................................7 HYDRAULIC ROUTING INSTRUCTIONS ............................ 7 PARTS LIST ....................................8 INSTALLATION LOCATIONS ..............................9 OPTIONAL ATTACHMENTS .............................. -
Page 4: Introduction
The Bauman Drop Spreader is capable of spreading sand, salt, grit, or similar materials and should only be used for this purpose. Correct usage of the machine also includes following the factory’s preparation, operation and maintenance instructions. -
Page 5: General Information
GENERAL INFORMATION The operator must read and understand the information in this manual to ensure the correct service and operation of the machine and avoid unnecessary risk of accidents and breakdowns. Please Note: Stop the tractor engine before you adjust, lubricate, or repair the machine. Remember to remove the ignition key to make sure no one starts the tractor while you are repairing the machine. -
Page 6: Safety Instructions
This concerns your safety. The Bauman Drop Spreader should only be operated by one person. The operator should ensure that no one is close to the area where the machine is in use. Do not let others operate the machine unless you are certain that they have the necessary knowledge to operate the machine safely and correctly. -
Page 7: Safety Labels
Bauman Drop Spreader. SAFETY LABELS The danger labels on Bauman Manufacturing equipment are for the safety of the operator as well as pedestrians and bystanders. Read and obey warning and danger labels. The operator must ensure that before operating the machine, all guards and grills are in place and that they are attached properly. -
Page 8: Maintenance
MAINTENANCE Warning: When repairing, maintaining and cleaning the machine, it is particularly important to be aware of the safety precautions. Park the tractor (if connected) as a precautionary measure and disconnect power when servicing. Do not clean, lubricate or adjust the machine before the tractor engine has been stopped and the parking brake is activated. -
Page 9: Spreading Material
SPREADING MATERIAL REGULATING SPREAD QUANTITY The spreading quantity is adjusted with the tension adjustment lever. Correct adjustment is important. If the adjustment is too tight, unnecessary wear of the rubber belts or rotating parts may occur. If the adjustment is too slack, distribution of material will be uneven. Hydraulic Units: All hydraulic units are equipped with hydraulic flow control. -
Page 10: Parts List
HYDRAULIC MOTOR - 5/8" ORB PORTS DECALW803 KEEP HANDS/FEET AWAY DECALSW404 MOVING PART HAZARD DECAL 1040B DECAL 1040B, MODEL # FOR 1040B DECAL SERIAL # SERIAL # DECAL 1140 SB50-4 RUBBER FLAP FINGER BAR 40 1140 SB60-4 RUBBER FLAP DISTRIBUTOR DRUM 40... -
Page 11: Installation Locations
INSTALLATION LOCATIONS... -
Page 15: Optional Attachments
OPTIONAL ATTACHMENTS ALO BRACKET Part Number: BRACKET ALO 3 POINT HITCH TILTING BRACKET Part Number: BRACKET 3PT TILT SKID STEER LOADER BRACKET Part Number: BRACKET SSL B... -
Page 16: Warranty Information
Bauman Manufacturing has been advised of the possibility of such damages. Except as provided herein, Bauman Manufacturing makes no warranties, expressed or implied, including without limitation, the implied warranties of merchantability and fitness for a particular purpose, with respect to the components.
Need help?
Do you have a question about the 1040B and is the answer not in the manual?
Questions and answers