Table of Contents
Advertisement
Quick Links
JV300- 1 30/ 1 60, JV300- 1 30/ 1 60 Pl u s BS INK MODEL Pri n t Gui d e
JV300-130/160 BS INK MODEL
JV300-130/160 Plus BS INK MODEL
Thank you for purchasing our inkjet printer JV300-130/160 BS INK MODEL, JV300-130/160 Plus BS INK
MODEL. This "Print Guide" explains the printing method using JV300-130/160 BS INK MODEL, JV300-130/160
Plus BS INK MODEL and the software RIP [RasterLink] and items to be checked/set before printing.
Note
• It is strictly prohibited to write or copy a part or whole of this document without our approval.
• This document has been carefully prepared for your easy understanding, however, please do not hesitate to
contact a distributor in your district or our office if you have any inquiry.
• Description contained in this document are subject to change without notice for improvement.
• Due to improvement or change of software, the description of this document could be partially different in
specification, for which your understanding is requested.
• With the exception of what is provided for in the warranty provisions of MIMAKI ENGINEERING CO., LTD., we
do not assume any liability against the damages (including but not limited to the loss of profit, indirect damage,
special damage or other monetary damages) arisen out of the use or failure to use of this product. The same
shall also apply to the case even if MIMAKI ENGINEERING CO., LTD. had been notified of the possibility of
arising damages in advance. As an example, we shall not be liable for any loss of the media (works, sheets)
made using this product or indirect damages caused by the product made using this media.
• You can also download the latest operation manual from our website.
RasterLink is the trademarks or registered trademarks of MIMAKI ENGINEERING CO., LTD. in Japan and in other
countries.
Adobe, Illustrator, Photoshop are the trademarks or registered trademarks of Adobe Systems Incorporated in the
United States and other countries.
Other company and product names mentioned herein are the trademarks or registered trademarks of the respective
companies in Japan and in other countries.
Unauthorized reproduction of any portion of this document is strictly prohibited
Print Guide
© 2014 MIMAKI ENGINEERING Co., Ltd.
Advertisement
Table of Contents
Related Manuals for MIMAKI JV300-130 Plus BK INK
Summary of Contents for MIMAKI JV300-130 Plus BK INK
- Page 1 • With the exception of what is provided for in the warranty provisions of MIMAKI ENGINEERING CO., LTD., we do not assume any liability against the damages (including but not limited to the loss of profit, indirect damage, special damage or other monetary damages) arisen out of the use or failure to use of this product.
-
Page 2: Frequently Asked Questions
Test print Feed rate corrction (Media correction) Ink drop position correction（Dot position correction） Prepare the Mimaki Driver. (Refer to P. 5) Install Mimaki Driver. Prepare the RasterLink. (Refer to P. 5) The preparation of RasterLink is explained. -
Page 3: Preparation Before Use
Preparation before use. About system configuration. Instruct to print the printing data created with the application such as Illustrator or Photoshop etc. from the PC in which the RasterLink has been installed. PC to create image data Send image data to a PC installed RasterLink Instruct to print from RasterLink. - Page 4 Prepare the printer. Following the procedures below, prepare the printer. Connect the PC installed RasterLink to the printer. • For details, refer to Chapter 1 “Connecting Cables” of the printer "Operation Manual". Turn on the printer. • For details, refer to Chapter 2 “Turning the Power ON”...
-
Page 5: Prepare The Mimaki Driver
• For the installation, refer to "Installation Guide" of the Mimaki Driver. • The Mimaki driver installation guide can be found in the Mimaki driver installer. • About the name of the installer For the included Driver software CD: mkcdmenu.exe When downloaded from our website: mkdriver_v***.exe... - Page 6 (2) Set the printer information. (The setup procedure described below assumes that JV300 BS INK MODEL is connected. Set the printer information in the following order:) • Model : JV300 • Color : Select depending on the device. • Output Port : USB2.0 •...
-
Page 7: Perform Printing
Perform printing. Here, an example using the image "sample.eps" is explained. • Check P. 3 to P. 5 “Preparation before use.” without fail before creating a seal/a sticker. Double-click the icon of the RasterLink to start the RasterLink. Select [File] - [Open] from the menu. •... - Page 8 Select the file loaded into the [JV300 BS INK MODEL] tab. To check or edit the settings, from [Function icons] displayed in the right side of the window, select the icons shown below. • For details about each function icon, refer to "Reference Guide"...
-
Page 9: Download The Profile Suitable For The Using Condition
Download the profile suitable for the using condition. Here, the download method of the profile suitable for the ink set to use is explained. Read this by replacing the printer/ the profile with the one you use. Start the Profile Update. (1) Select [RasterLink] - ([Update] - ) [Profile Update] from the Start menu. - Page 10 (1) Select the profile to install, and click [Next] (2) Click [Finish]. • The profile is installed when RasterLink is started next. Refer to "Installation Guide" of the RasterLink for details. • You can also download the profile from our website. (https://mimaki.com/) - 10 -...
-
Page 11: Typical Questions
Typical questions. The answers to the questions/ the troubles frequently asked by the customer are provided. About errors. “Replace a Wiper” appears on the display. Time for replacement of the wiper has come. Replace the wiper by following the procedures in Chapter 4 “Replacing the wiper”... - Page 12 D202695-12-27082020 © MIMAKI ENGINEERING CO., LTD.2014...
Need help?
Do you have a question about the JV300-130 Plus BK INK and is the answer not in the manual?
Questions and answers