Related Manuals for Toro 30887
Summarization of Contents
Introduction
General Safety
Essential safety guidelines for operating the machine.
Safety
General Safety
General safety rules to prevent injury and damage.
Rollover Protection System (ROPS) Safety
Safety requirements and usage of the Roll Over Protection System.
Preparing the Machine
Installing the Mulching Baffle
Optional procedure for installing the mulching baffle.
Controls
Traction Pedal
How the traction pedal controls movement and braking.
Brake Pedals
Operation of the individual wheel brake pedals.
Key Switch
Operation of the ignition key switch positions.
Specifications
Machine Specifications
Detailed specifications table for 4500-D and 4700-D models.
Cutting Unit Specifications
Specifications for the cutting units used on the machine.
Operation
Before Operation
Pre-operation checks and safety precautions.
Fuel Safety
Safety precautions for handling and using fuel.
Filling the Fuel Tank
Fuel Specification
Recommended diesel fuel types and standards.
Selecting a Blade
Standard Combination Sail
Description and attributes of the standard blade.
Angled Sail (Not CE Compliant)
Performance characteristics of the angled sail blade.
High-Lift Parallel Sail (Not CE Compliant)
Performance characteristics of the high-lift parallel sail blade.
Atomic Blade
Description and attributes of the atomic blade for mulching.
Using the Menus
Settings
Customizing and modifying machine configuration settings.
Protected Menus
Accessing Protected Menus
Step-by-step guide to access protected menus with a PIN.
Viewing and Changing the Protected Menu Settings
Setting the Maximum Allowed Mow Speed
How to set the maximum mowing speed.
Setting the Maximum Allowed Transport Speed
How to set the maximum transport speed.
Setting the Acceleration Mode
How to select the acceleration and deceleration mode.
During Operation
During Operation Safety
Safety precautions to follow while the machine is in use.
Rollover Protection System (ROPS) Safety
Safety requirements and usage of the Roll Over Protection System.
Understanding the Operating Characteristics of the Machine
Operating the Machine
Step-by-step guide to starting and operating the machine.
Operating the Cruise Control
Setting the Cruise Control
How to set and use the cruise control for maintaining speed.
Diesel Particulate Filter Regeneration
Engine Warning Messages—Soot Accumulation
Interpretation of engine warnings related to soot accumulation.
Reset Regeneration
Setting the Inhibit Regen Reset Regeneration Only
How to inhibit reset regeneration using the InfoCenter settings.
Parked or Recovery Regeneration
Parked Regeneration Messages
Displays and meanings of messages for parked regeneration.
Operating Tips
Selecting the Proper Height-of-Cut Setting to Suit Conditions
How to select height-of-cut based on grass conditions.
Mowing with Sharp Blades
Importance of sharp blades for grass health.
After Operation
General Safety
Safety precautions to follow after operating the machine.
Using the Cutting-Unit Storage Lanyard
How to use storage lanyards for cutting units.
Maintenance
Maintenance Safety
Safety precautions to follow during all maintenance tasks.
Recommended Maintenance Schedule(s)
A schedule outlining recommended maintenance procedures and intervals.
Pre-Maintenance Procedures
Lifting the Machine
Safe points and methods for lifting the machine.
Lubrication
Greasing the Bearings and Bushings
How to properly grease bearings and bushings.
Engine Maintenance
Servicing the Air Cleaner
How to service and replace the air cleaner filter.
Servicing the Engine Oil
Checking the Engine-Oil Level
How to check the engine oil level correctly.
Fuel System Maintenance
Draining the Fuel Tank
How to drain and clean the fuel tank.
Servicing the Fuel-Water Separator
Draining Water from the Fuel/Water Separator
How to drain water and contaminants from the separator.
Electrical System Maintenance
Checking the Battery Condition
How to check the battery's condition and perform cleaning.
Drive System Maintenance
Checking for End-Play in the Planetary Drives
How to check for excessive movement in the planetary drives.
Checking the Planetary Gear-Drive Lubricant
How to check the lubricant level in the planetary gear-drive.
Cooling System Maintenance
Cooling System Safety
Safety precautions related to the cooling system.
Checking the Cooling System
How to check the engine coolant level.
Brake Maintenance
Adjusting the Service Brakes
How to adjust the service brakes for proper function.
Belt Maintenance
Servicing the Alternator Belt
How to service and adjust the alternator belt tension.
Hydraulic System Maintenance
Hydraulic System Safety
Safety precautions for working on the hydraulic system.
Servicing the Hydraulic Fluid
Procedures for servicing the hydraulic fluid.
Checking the Hydraulic-Fluid Level
How to check the hydraulic fluid level.
Cutting Unit Maintenance
Removing the Cutting Units
How to safely remove the cutting units from the machine.
Installing the Cutting Units
How to safely install the cutting units onto the machine.
Blade Maintenance
Blade Safety
Safety precautions when working with mower blades.
Inspecting the Blade Plane
How to inspect the blade plane for accuracy.
Storage
Storage Safety
Safety precautions to follow when storing the machine.
Preparing the Machine for Storage
Steps to prepare the machine for long-term storage.
Need help?
Do you have a question about the 30887 and is the answer not in the manual?
Questions and answers