Forklift stabilization kit for toughtek f680e pump (2 pages)
Summary of Contents for Graco 24H663
Page 1
Instructions Swivel Kit or Hose Replacement Kit for LD Series Enclosed Hose 313939E Reels - Swivel or Hose Reel Replacement Instructions - Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. For complete Warnings and instructions, see the LD Series Enclosed Hose Reel instruction manual. Parts Included in Swivel Kit Ref No.
Page 2
Swivel Kit Part Nos.: Part No. Models Material Maximum Working Pressure 24F789 - 24F794 24C531 Air, A/W 250 psi (1.7 MPa / 17.2 bar) 24J126 - 24J131 24F795 - 24F796 24C532 1800 psi (12.4 MPa / 124.1 bar) 24J132 - 24J133...
Page 3
Warnings Warnings WARNING SKIN INJECTION HAZARD High-pressure fluid from dispense device, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment. •...
Page 4
Instructions Instructions Disassembly IMPACT HAZARD The spring is always under great tension and could be propelled or uncoil with enough force to cause serious injury. • The hose reel spring is not a serviceable part. Do not attempt to replace or service the spring. •...
Page 5
1/4 turns needed to completely Full Turns to Increase 1/4 Turns to Model release the spring tension. Spring Tension Decrease Spring Tension 24F789 - d. Turn ratchet 1/8 turn counter-clockwise and 24F797 remove ratchet. 24H655 - 24H663 24J126 - 24J134...
Page 6
Instructions 4. To remove hose reel from service: a. Insert a screw driver in opening (b) to depress spring pin on mounting tube (F . 7). ti13512 5. Slide tube (c) out of bracket (F . 8). 6. Remove hose reel from mounting bracket (d) (F 9) and lay hose reel on a work bench or flat work surface.
Page 7
Instructions 7. Remove all screws (e) from side enclosure (f) and 9. Remove hose guide roller (k) from enclosure (j). remove enclosure from hose reel (F . 10). Do not 10. Holding spool and enclosure (j) together, turn over discard these parts, you will need them for reassem- hose reel assembly.
Page 8
Instructions NOTE: If you are replacing the swivel assembly, con- Hose Replacement Disassembly tinue with Step 13, (below). If you are just replacing 1. Perform Steps 1 - 12 (page 4 - 7). the hose, skip Step 13 and go to the Hose Replace- ment Disassembly instructions.
Page 9
Instructions 2. Connect hose fitting (m) to swivel assembly. (F Continue Hose Replacement Installation 18). Instructions Here 2. Replace side enclosure (j) over spool using new screws (1) (F . 20). Torque to 0.07 - 0.1 N.m (10 - 15 in. pounds). .
Page 10
Instructions 4. Feed end of hose through hose guide in enclosure 7. Align hose reel with mounting bracket (d). Slide and install hose guide rollers (k) in enclosure (j) on mounting tube (c) through hose reel enclosure and either side of hose (F .
Page 11
Instructions 9. Connect supply hose (a) to swivel (F . 26). NOTE: After hose reel is installed and returned to ser- vice, it may be necessary to reposition the ball stop. To reposition ball stop (F . 28): a. Loosen screws (n) and nuts (p). b.
Page 12
Original instructions. This manual contains English. MM 313939 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA Copyright 2009, Graco Inc. All Graco manufacturing locations are registered to ISO 9001. www.graco.com...
Need help?
Do you have a question about the 24H663 and is the answer not in the manual?
Questions and answers