Graco 15V534 Instructions - Parts Manual
  1. Manuals
  2. Brands
  3. Graco Manuals
  4. Racks & Stands
  5. 15V534
  6. Instructions - parts manual
Graco 15V534 Instructions - Parts Manual

Graco 15V534 Instructions - Parts Manual

Gun flush box; interface kit
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Instructions-Parts
15V534 Gun Flush
Box Interface Kit
Interfaces a Graco Gun Flush Box with a ProMix
RoboMix Fluid Station. For professional use only.
Approved for use in explosive atmospheres only when used in conjunction with ProMix
2KS Electronic Proportioners.
100 psi (0.7 MPa, 7 bar) Maximum Air Input Pressure
Important Safety Instructions
Read all warnings and instructions in this manual. For complete
warnings and instructions see your proportioning system manual
and gun flush box manual 312784. Hazard symbols refer to spe-
cific procedure risks. Save all instructions.
GFB Interface Kit shown with
two air flow switches installed
®
2KS Electronic Proportioner using a
2575
II 2 G
313212B
ENG
TI14275a

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 15V534 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Graco 15V534

Summary of Contents for Graco 15V534

  • Page 1 15V534 Gun Flush Box Interface Kit 313212B ® Interfaces a Graco Gun Flush Box with a ProMix 2KS Electronic Proportioner using a RoboMix Fluid Station. For professional use only. Approved for use in explosive atmospheres only when used in conjunction with ProMix 2KS Electronic Proportioners.

  • Page 2: Table Of Contents

    Technical Data ......13 Graco Standard Warranty ....14...

  • Page 3: Installation

    Installation Installation Location Install the gun flush box module enclosure (1) within 15 ft (4.5 m) of the RoboMix, to ensure that the cable (23) will reach the RoboMix. The module is approved for use • To avoid electric shock, ground all equipment. in a hazardous location.

  • Page 4: Install The Cable

    Installation Install the Cable 3. Connect the cable wires to the left side of the termi- nal strip (12), as indicated by the label (20). See F 2 and Table 1. 1. Loosen the captive screws and remove the front cover from the enclosure.

  • Page 5: Install The Air Flow Switch

    Installation Install the Air Flow Switch 2. Connect the wires from AFS#1 to the right side of the terminal strip (12) pins 1 (+) & 2 (-), as indicated by the label (21). See F . 4 and Table 1. NOTE: The GFB Interface Module Kit does not include an air flow switch (AFS).

  • Page 6: Install The Pressure Switch

    Installation Install the Pressure Switch 2. Connect the wires from PS#1 to the right side of the terminal strip (12) pins 5 (+) & 6 (-), as indicated by the label (21). See F . 6 and Table 1. NOTE: The GFB Interface Module Kit does not include a pressure switch (PS).

  • Page 7: Install The Solenoid

    Installation Install the Solenoid 2. Connect the wires from SO#1 to the right side of the terminal strip (12), as indicated by the label (21); red (+12V) to pin 9, black (COM) to pin 10. See F NOTE: The GFB Interface Module Kit does not include a and Table 1.

  • Page 8: Connect The Cable To The Robomix Control Board

    Installation Connect the Cable to the RoboMix Control Board NOTICE To avoid damaging circuit board when servicing, wear grounding strap on wrist and ground appropriately. 1. See the ProMix 2KS Repair-Parts manual. Open the RoboMix to access the control board. 2.

  • Page 9: Connect The Gun Flush Box

    Installation Connect the Gun Flush Box Replace the Cover NOTE: Use 5/32 in. (4 mm) OD tubing to connect the Reinstall the cover on the enclosure and secure with the gun flush box air ports to the interface module air ports, four captive screws.
  • Page 10 Installation 313212B...

  • Page 11: Parts

    Parts Parts TI14279a 1 (Ref) TI14280a If using two gun flush boxes, remove item 5 and two of item 4. 12 (Ref) AIR FLOW SWITCH #1 + (BLK) AIR FLOW SWITCH #1 - (WHT) AIR FLOW SWITCH #2 + (RED) AIR FLOW SWITCH #2 - (GRN) PRESSURE SWITCH #1 + (ORG) PRESSURE SWITCH #1 - (BLU)

  • Page 12: Connect A Booth Control To The Robomix (To Operate As A Manual System)

    Connect a Booth Control to the RoboMix (to operate as a manual system) Connect a Booth Control to the RoboMix (to operate as a manual system) To use the RoboMix as a manual system, order the 1. See F . 13. Mount the booth control in a convenient 15V350 Booth Control Kit and connect as follows.

  • Page 13: Dimensions

    Dimensions Dimensions 4.00 in. 4.00 in. (101.6 mm) (101.6 mm) 6.75 in. (171.5 mm) 7.50 in. Mounting Holes (190.5 mm) 6.28 in. (159.5 mm) TI14276a TI14278a Technical Data Maximum Air Input Pressure ..... 100 psi (0.7 MPa, 7 bar) Air Inlet Size .

  • Page 14: Graco Standard Warranty

    With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.

Table of Contents