Related Manuals for Interlogix Advisor Advanced ATS1000A-SM
Summarization of Contents
General installation information
Advisor Advanced housings
Details on the physical housings for Advisor Advanced control panels, including dimensions and mounting holes.
Maintenance
Mains power connection
Instructions for safely connecting the control panel to the AC mains power supply.
Battery replacement
Procedures and safety precautions for replacing the rechargeable battery.
Mounting
General installation guidelines
Guidelines for installing the Advisor Advanced control panel, ensuring safety and performance.
Cabling Advisor Advanced
System databus preferred wiring
Details on the preferred wiring configuration for the system databus.
Zone connection
Single loop zone wiring
Instructions for wiring single loop zones, including alarm and tamper connections.
Other connections
Tamper connection
Wiring instructions for earthing, external tamper, and PSTN connections.
Configuration
Defaulting the panel
Procedure for setting default configuration values during initial panel setup.
Zone configuration
Options for expanding and configuring system zones via internal and external expanders.
Outputs
Information on panel outputs and how to expand them using output expanders.
Specifications
General features
Overview of system capabilities including code combinations, zone/output limits, and data retention.
Standard onboard outputs
Details on the specifications and ratings of the panel's standard electronic outputs.
Common key sequences
Common key sequences for LCD keypad
Table of common programmed methods and key sequences for operating the LCD keypad.
The Advisor Advanced menu
User code requirement
Explanation of the system's requirement for user codes for menu access.
Challenge code requirement
Details on the challenge code system for accessing programming menus.
How to program the options
Accessing the installer programming menu
Step-by-step guide to accessing the installer programming menu.
Service
Service menu
Overview of options available in the Service menu for commissioning and maintenance.
Test options
Input tests
Procedures for testing system inputs, including showing open zones and RF signal strength.
Outs&triggers
Output test
Instructions for testing system outputs and LEDs.
Devices
Installed remote devices
Displaying the status of all connected remote keypads and expanders.
Keypads
Keypad devices
Managing keypad devices, including adding and selecting them for configuration.
Keypad options
Configuration settings specific to keypads, such as name, tamper area, and view areas.
Expanders
Expander devices
Managing expander devices, including adding and selecting them for configuration.
Wireless specific options
Supervision
Configuration of supervision timers for wireless devices to detect communication loss.
Camera specific options
Pic options
Settings for configuring photo recording options for camera events.
Users and user groups
User menu
Access to menus for adding, editing, or deleting users and user groups.
Users
Add user
Procedure for adding new users to the Advisor Advanced system.
Predefined users
Information on the default Installer and Supervisor users and their assigned groups.
User groups
User group options
Configuration of user group privileges, defining access rights to system options.
Zones, fobs, and cameras
Zones and RF fobs
Programming section for all zone and fob parameters, covering physical inputs and wireless devices.
Zones
Zone menu
Interface for viewing, selecting, or creating new zones.
Zone options
Configuration settings for zones, including name, type, and area assignments.
Shock sensor options
Gross and Pulse options
Configuration for shock sensor pulse count and gross level settings.
Wireless sensor options
RF details
Programming wireless devices manually or removing them from the expander database.
Fobs
RF fobs
Menu for viewing programmed fobs, selecting existing ones, or creating new ones.
Fob options
Configuration settings for fobs, including name, assigned user, and button functions.
Cameras
Cameras
Configuration menu for camera modules in wireless PIR cameras.
Select camera
Procedure for selecting and configuring a specific camera module.
Areas
Area menu
Menu for programming area-specific options like name, entry/exit times.
Select area
Procedure for selecting an area to program its specific settings.
Filters, outputs, and triggers
Outputs and filters
Programming section for outputs, condition filters, and system triggers.
Condition filters
How condition filter works
Explanation of how condition filters operate and can be used to control outputs.
Outputs
Outputs
Menu for managing system outputs, including adding, selecting, and configuring them.
Action lists
Action lists
Grouping configured actions into lists for automatic execution and management.
Exceptions
Exceptions
Defining specific time periods that override or substitute everyday actions.
Add exception
Procedure for adding new exceptions with start and stop dates, and associated actions.
Schedules
Schedules
Timed sets of actions with a weekly structure, including activation and date ranges.
Select schedule
Procedure for selecting and programming schedule parameters.
System options
System option menu
Global system options including timers, engineer options, and LCD display settings.
Timer menu
Configuration of system-wide timers for sirens, system miscellaneous options, and zone timers.
LCD display options
Armed display
Settings for the armed display mode on keypads, including options like Always or Off.
Forced set
Forced set options
Configuration defining when forced set is possible, including inhibit options.
Zones
Zone options
Configuration of zone inputs, including input mode and end-of-line (EOL) resistor values.
Input mode
Determines how zone inputs are configured, supporting single NO, single NC, and dual loop modes.
EOL
Defines end-of-line resistor values for expander zone inputs.
Panel and AB options
Panel name
Allows changing the panel's name for identification.
Panel language
Allows changing the panel's display language.
Other options
PA and other
Configuration for panic alarm mode, chime, and buzzer options.
Communications
Dialler menu
Programming section for all system-wide communication options.
Central stations
Central station
Programming up to 16 central stations, including common and specific transmission path options.
CS name
Screen to enter or change the central station name.
PSTN and ISDN specific options
Phone
Configuration of telephone numbers for central station reporting.
IP and GSM/GPRS specific options
Destination/IP
Defining IP details for PC connections and pinging the host.
GSM specific options
Conn. type
Defines the GSM connection type used, either CSD or GPRS.
Events
Event options
Configuration of event options, including CS mapping, voice mapping, and delayed events.
Communication paths
Path options
Configuration of options for available transmission paths like PSTN, IP, ISDN, GSM.
Select path
Procedure for selecting and configuring options for a specific transmission path.
GSM/SMS/GPRS specific options
GSM Setup
Setup menu for GSM reporting and control, including SIM card PIN and network settings.
PC connections
PC connection
Setting up PC connection parameters for upload/download, management, and remote control.
Connections
Managing PC connections, including adding, selecting, and deleting them.
User programmable functions
Programming menu
Access to menus for programming user functions, defining parameters and activation methods.
Wireless device programming
Learning wireless sensors
Procedures for learning wireless sensors in sequential or manual modes.
Using cameras
Configuration
System configuration for wireless PIR cameras, including activation events and event types.
Camera event types
List of available camera event types, such as Burglar, Fire, Panic, and Medical alarms.
Alarm reporting principles
Event conditions
Checks performed by the system before reporting new events to central stations.
Programming Advisor Advanced via configuration software
First connection of the Advisor Advanced panel to the PC
Steps for connecting the control panel to a PC for the first time, including software installation.
Upgrading Advisor Advanced firmware
Installing AAFlash on the PC
Instructions for installing the AAFlash software required for firmware upgrades.
Connecting Advisor Advanced to the PC
Procedure for connecting the panel to a PC for firmware upgrades via USB DFU.
Troubleshooting
Recovery procedure
Steps to recover installer access if the installer PIN is lost.
Options affected by EN 50131 regulations
EN 50131 Grade 2
Mandatory settings and values required for EN 50131-1 Grade 2 compliance.
Options affected by other regulations
ACPO policy
Modifications required for ACPO policy compliance, including entry alarms and alarm confirm settings.
INCERT policy
Required settings for INCERT policy, including user group options and PIN length.
Need help?
Do you have a question about the Advisor Advanced ATS1000A-SM and is the answer not in the manual?
Questions and answers