Customising The Cr104; Code Learning - Arcam BDP100 Handbook

customising
the CR104

code learning

The Cr104 comes with a complete library of
preprogrammed codes. After you have set up the Cr104
for your device, you may find that there are one or more
functions on your original remote which do not have a
place on the Cr104 keypad. For convenience, the Cr104
offers a Code Learning feature that allows you to copy
up to 16 functions from an original remote control onto
the Cr104 keypad.
Before you start, make sure that:
The original remote control is working correctly.
<
The remotes are not pointing at your device.
<
The remotes have new batteries.
<
The remotes are not in direct sunlight or under
<
strong fluorescent lights.
Learned functions are mode-dependent: You could
theoretically assign up to eight different functions
to a single key (the Cr104 can handle a total of 16
learned functions).
example: To copy the 'text hold' function
from a TV remote onto the ( key of your
cR104
1. Place both remotes on a flat surface, 2 to 5cm
apart, with the Ir ports facing each other.
On the Cr104, press and hold S until the power
2.
LED blinks twice: * * .
Press 9 7 5 . The power LED blinks twice:
3.
* * .
4. On the Cr104, press the device key that matches
the 'source' device (e.g. if you're learning a TV
function, press a ).
5. On the Cr104, press the key to which you want to
assign the learned function (e.g. ( ). The device
key blinks rapidly.
6. On the original remote, press and hold the
function key that you want to learn (e.g.
) until the Cr104 device key blinks
TExT HOLD
twice: * * .
7. If you want to learn other functions from the
same source device, simply repeat steps 5 and 6
pressing the next key you want to learn.
To exit Code Learning mode, press and hold S
8.
until the device key blinks twice: * * .
9. To use the learned function on the Cr104, press
the Device Mode key, followed by the function
key.
In this example, you' d press
a followed by (
Shifted learning
You can assign a learned function to a Cr104 key
without sacrificing its original function.
You can assign Shifted Learning functions to any key
except for: Device Mode keys (e.g. a ), S , or number
keys ( 0 to 9 ).
1. To assign a Shifted Learning function, simply
follow Code Learning steps in the previous
section. During step 5, press S once before you
press the key to which you want to assign the
learned function.
To access the shifted function, press S and then
2.
the target key.
important notes
Once you start a Code Learning session, you have
<
approximately 10 seconds to conduct each step.
Any longer, and a timeout means that you'll have
to start the process again.
The Learning feature is mode-specific – you can
<
copy one feature per mode onto a key.
The Cr104 can learn approximately 16 functions
<
in total.
To replace a learned function, simply assign a new
<
one to the same key.
Learned functions are retained when you change
<
batteries.
If Code Learning fails, try altering the distance
<
between the two remotes; make sure that the light
in the area is not too bright.
To delete a learned function
Press and hold S until the power LED blinks
1.
twice: * * .
Press 9 7 6 . The power LED blinks twice: .
2.
3. Press a Device Mode key once. For example, if you
want to delete one of your learned TV functions,
press a .
4. Press twice on the key you want to deassign. The
handset blinks twice: * * to confirm.
e-26
The original function of the Cr104 is restored.
To delete a Shifted learned function:
To delete a Shifted Learned function, press S before
you press the key to be deassigned (during step 4 above).
To delete all learned functions within a
given device Mode
Press and hold S until the power LED blinks
1.
twice: * * .
Press 9 7 6 – the power LED blinks twice:
2.
* * .
3. Press the appropriate Device Mode key twice.