Parental Control - Arcam BDP100 Handbook

display
TV Type – Set the video signal format. If the colour or
picture quality of analogue video appears incorrect,
change this setting. It should not need to be adjusted in
normal use.
NTSC: USA and Canada video standard.
<
PAL: Europe, Australia and China video standard.
<
Resolution – Set the video resolution of the and
HDMI
outputs.
COMPONENT VIDEO
HDMI Auto: Sets the TV's preferred resolution.
<
1080p: Full HD progressive video.
<
1080i: interlaced HD video.
<
720p: progressive HD video.
<
480p/576p: 480 lines (nTSC) or 576 lines (PAL)
<
progressive video
480i/576i: 480 lines (nTSC) or 576 lines (PAL)
<
Standard Definition interlaced video.
NOTE
The HDMI Auto setting may not set the best
<
possible resolution. If you have a 1080p Full
HD display, set the resolution to 1080p.
For full details of output resolutions available
<
at different outputs, refer to the table on page
E-25.
TV Aspect – Set the aspect ratio (shape) of your display.
16:9 Wide: Use with widescreen TVs. 4:3 material
<
will be zoomed to fit the screen.
16:9 Pillarbox: Use with widescreen TVs. 4:3
<
material will be displayed in full, with vertical
black bars at the sides.
4:3 Pan and Scan: Use with 4:3 non-widescreen
<
TVs. 16:9 widescreen content will be displayed
with the left- and right-hand sides of the image
cropped to fit the screen (no black bars). The
aspect ratio will be maintained (the image will not
be stretched).
4:3 Letterbox: Use with 4:3 non-widescreen TVs.
<
16:9 widescreen content will be displayed with
black bars at the top and bottom.
24p Mode – Enable or disable 24 frames-per-second
video output (1080/24p).
On: Select to output 24p signals from the
< HDMI
output.
Off: Disable 24p video output.
<
NOTE
1080/24p video signals can only be output
<
using the connection.
HDMI
The connected equipment (AV receiver, TV/
<
projector) must be 1080/24p compatible.
The output resolution must be set to 1080p or
<
HDMI Auto.
Color Depth – Set the level of Deep Color processing
applied to the HDMI video output.
36-bit: Select to output 36-bit Deep Color signals
<
from the output.
HDMI
30-bit: Select to output 30-bit Deep Color signals
<
from the output.
HDMI
24-bit: Select to output 24-bit standard color
<
signals from the output (Deep Color off).
HDMI
NOTE
The connected equipment (AV receiver, TV/
<
projector) must be Deep Color compatible
in order to use 30/36-bit Deep Color signals.
refer to your TV & AV receiver user manual.
All system HDMI interconnect cables must
<
be Deep Color compatible in order to use
30/36-bit Deep Color signals.
If you experience a flickering or abnormal
<
picture after changing the Deep Color
setting, connect the unit using a Composite
video cable and change the setting to a value
supported by the display.
audio
PCM Downsampling – Set the maximum sample
rate of audio output from the or
OPTICaL COaxIaL
DIgITaL OuT.
96kHz: Output digital audio with a 96kHz sample
<
rate (best quality).
48kHz: Output digital audio with a 48kHz sample
<
rate (most compatible).
NOTE
If the connected equipment (e.g. AV receiver)
<
does not support 96kHz, silence or loud noise
may result from this setting. If this happens,
set PCM Downsampling to 48kHz.
Digital Output – Sets the audio format output from the
, or
HDMI OPTICaL COaxIaL DIgITaL OuT.
Bitstream HD: Output the HD bitstream Blu-ray
<
Disc soundtrack for decoding in your AV receiver
( output only, requires compatible AV
HDMI
receiver).
Bitstream Legacy: Output the relevant legacy
<
format for the soundtrack. This option is suitab;e
for older AV receivers that are not HD, HDMI
Audio or DTS compatible.
Bitstream Mixed: Convert all surround audio to
<
DTS 5.1 surround format. This option gives the
best quality for DTS-compatible AV receivers that
are not HD or HDMI Audio compatible.
PCM 7.1: Decodes all formats within the player
<
and outputs PCM audio. Use this option for HD
receivers that cannot decode all HD formats. The
and digital outputs will output
OPTICaL COaxIaL
stereo PCM audio.
PCM 5.1: As PCM 7.1 but any HD 7.1-format
<
surround soudtracks will be converted to 5.1-
format surround ( output only).
HDMI
PCM Stereo: Decodes all formats within the
<
player and outputs PCM audio. All surround-
sound formats are converted to stereo on all audio
output connections.
NOTE
The signal at the output is also
< HDMI
determined by the formats supported by the
connected equipment.
For full details of output formats, refer to the
<
table on page E-25.
Dynamic Range Control – Set whether to compress the
dynamic range between the loudest and softest sounds
when a Dolby Digital, Dolby Digital Plus or
DolbyTrueHD audio is played back.
On: Turns on Dynamic range Control so that
<
quiet sounds can be heard more easily.
Off: Turns Dynamic range Control off.
<
Auto: Allows coding embedded within a Dolby
<
TrueHD soundtrack to set the dynamic range. For
other soundtracks, responds the same as 'On'.
e-21
language
OSD – Set the language used for the On Screen Display
(OSD).
Menu – Set the language used for the Disc Menu and
Pop-up Menu.
Auto: Sets the priority language of the disc.
<
Audio – Set the language for the soundtrack.
Auto: Sets the priority language of the disc.
<
Subtitle – Set the language used for the subtitles.
Off: Displays no subtitles.
<
NOTE
The ability to select a particular language may
<
depend on the disc played.

Parental control

Parental control settings can be engaged to prevent
viewing of discs or scenes with material inappropriate
for children. A 4-digit code is required to enable or
disable Parental Control. Parental Control has various
levels; according to the level set, a disc may be stopped
or have certain scenes cut or substituted with alternative
scenes, depending on the disc.
To activate Parental Control:
1. Select the Parental Control menu:
u > >
Settings Parental Control
2. If Parental Control is set to On, you must enter your
PIn using the remote control numeric buttons.
The default PIn is 3308.
P leas e Input 4-Digit P arental P as s word :
P arental P as s word
OK C ancel
3. Once the Parental Control menu is accessed, press
' ,
the / cursor buttons on the remote to
>
select from the following items. Press to select
an item.