Related Manuals for Grant Solo Hideaway
Summary of Contents for Grant Solo Hideaway
- Page 1 Grant Solo Fan Convectors Installation and User Instructions UK | DOC 0139 | Rev 1.0 | October 2018...
- Page 2 This manual is accurate at the date of printing but will be superseded and should be disregarded if specifications and/or appearances are changed in the interests of continued product improvement. However, no responsibility of any kind for any injury, death, loss, damage or delay however caused resulting from the use of this manual can be accepted by Grant Engineering (UK) Limited, the author or others involved in its publication.
-
Page 3: Table Of Contents
Regulations Control panel Location System requirements CLEaninG Pipework materials Pipe connections DECLaRatiOn OF COnFORmitY Installation procedure: Solo Compact and Solo HEaLtH anD saFEtY inFORmatiOn CompactMAX models Installation procedure: EnD OF LiFE inFORmatiOn Solo Hideaway model GUaRantEE ELECtRiCaL General Electrical connections... -
Page 4: Introduction
Each Solo fan convector requires a 3A fused 230V 1ph 50Hz electrical supply. Refer to Section 5 for further details. A double pole mains ON/OFF switch is factory fitted to all Grant Solo units. Control panel On the Solo Compact and CompactMAX models this is located under the right-hand end of the front casing. -
Page 5: Control Panel Overview
‘Low’ or ‘High’ setting as dictated by the difference between the air temperature and the air temperature setting on the unit. COntROL PanEL OVERViEW Grant Solo fan convectors are supplied with a simple control panel. Refer to Figure 1-3 and Section 8.2 (control panel). ON/OFF... -
Page 6: Technical Data
Data Fan COnVECtOR tECHniCaL Data table 2-1: Fan convector technical data Units solo Compact solo Compactmax solo Hideaway Height Width Depth Water content litres 0.15 0.30 0.15 Weight (empty) 13.8 Weight (full) 8.35 14.1 6.75 Flow and return pipe size Maximum water temperature °C... -
Page 7: Installation
REqUiREmEnts Each Solo fan convector requires a 3A fused 230V 1ph 50Hz Grant Solo fan convectors can be used on either open vented or electrical supply and is fitted with a terminal block for easy and sealed central heating systems. -
Page 8: Pipework Materials
Safely store the front cover for now where it will not be Then, turn on the radiator(s) and adjust the lockshield valve damaged or scratched for re-fitting after the Solo Compact or on each radiator and reduce the flow until the fan convector(s) CompactMAX fan convector has been installed. -
Page 9: Installation Procedure
HiDEaWaY mODEL Accurately mark and cut the opening required in the plinth or panel into which the Grant Solo Hideaway unit is to be fitted. The bottom edge of the opening MUST be at least 12mm above the finished floor level. - Page 10 ! nOtE ! Do NOT fit the Solo Hideaway unit into the opening until the system has been filled and the fan convector(s) vented. When all the Solo fan convectors have been connected to the system pipework, the system can be filled. Once the system is filled, open the HIGHEST of the two bleed screws on the flow pipe to vent the fan convector heat exchanger.
-
Page 11: Electrical
See Figure 4-1. only. Connect the mains supply cable (from the fused double pole For the Solo Compact and Solo CompactMAX this switch can be switch) to the terminal block as follows: located on the wall next to the fan convector. -
Page 12: Fault Finding
FaULt FinDinG initiaL CHECKs If your Grant Solo fan convector appears not to be operating correctly, please first carry out the following simple checks before seeking further assistance. symptoms Check actions If NO: Check mains ON/OFF switch is set to ON Are there any lights on the control panel? ►... -
Page 13: Fault Diagnosis Flow Chart
! WaRninG ! The following flowchart can be used to determine and rectify a fault in the operation of a Grant Solo fan convector. Exposure to live electrical connections. Please first carry out the simple checks, as detailed in Section 6.1, before using the flow chart below. -
Page 14: Spares Parts
Flexible hose - 900 mm SP-MB90 • OPERatinG instRUCtiOns mains On/OFF sWitCH Grant Solo units have a factory-fitted double pole mains ON/OFF switch. sOLO COmPaCt anD COmPaCtmax mODELs: This switch is located under the right-hand end of the front casing. Refer to Figure 10-1. -
Page 15: Control Panel
CLEaninG Whilst it is not necessary for the Grant Solo fan convectors to be The warm air outlet grille on the top of the Solo Compact and Solo regularly serviced, a limited amount of cleaning is required from CompactMAX and the front grille of the Solo Hideaway can be time to time. -
Page 16: Declaration Of Conformity
Hopton Industrial Estate Devizes SN10 2EU Declare that: Equipment: Solo Fan Convector Radiators model name/number: Solo Compact, Solo CompactMAX and Solo Hideaway In accordance with the following Directives: Low Voltage Directive: 2014/35/EU EmC Directive: 2014/30/EU Radiator and Convector standards: EN 442-2... -
Page 17: End Of Life Information
For guidance on the disassembly of the fan convector refer to the information given in the Servicing section of these instructions. RECYCLinG Many of the materials used in Grant fan convectors can be recycled, these are listed in the table below: COmPOnEnt... -
Page 18: Guarantee
13 GUaRantEE You are now the proud owner of a Grant Solo fan convector from Free of charge repairs Grant Engineering (UK) Limited which has been designed to give During the five year guarantee period no charge for parts or years of reliable, trouble free operation. - Page 19 • This guarantee applies to Grant Engineering (UK) Limited fan convectors purchased and installed on the UK mainland, Isle of Wight, Channel Islands and Scottish Isles only .
- Page 20 GRant EnGinEERinG (UK) LimitED Hopton House, Hopton Industrial Estate, Devizes, Wiltshire, SN10 2EU Tel: +44 (0)1380 736920 Fax: +44 (0)1380 736991 Email: info@grantuk.com www.grantuk.com...
Need help?
Do you have a question about the Solo Hideaway and is the answer not in the manual?
Questions and answers