Operating Instructions - Denon AVR-2307CI Operating Instructions Manual

ENGLISH
Troubleshooting
Symptom
No sound is produced
• Subwoofer's power is not on.
from subwoofer.
• Subwoofer's initial setting is set to
"NO".
• Subwoofer's output is not connected.
• The subwoofer's channel volume
level is set to "OFF".
No test tones are • Surround mode is set to a mode
produced. other than STANDARD (Dolby/DTS
Surround).
No sound is produced • Surround mode is set to "STEREO".
from surround speakers.
This unit does not • Batteries dead.
operate properly when • Remote control unit too far from this
remote control unit is unit.
used. • Obstacle between this unit and
remote control unit.
• Different button is being pressed.
< >
• and ends of batteries inserted
in reverse.
• AVR-2307CI's HDMI output terminals
An image is not
and monitor's input terminals are not
projected with an HDMI
connection. properly connected.
• No HDMI signal is being input.
• The connected monitor equipment or
other equipments do not support
HDCP.
• The output format of the connected
player (HDMI FORMAT) does not
match the supported input format of
connected monitor equipments.
The HDMI audio is not • The AVR-2307CI does not play HDMI
output.
audio signals.
• The HDMI audio signals are not
output from the connected monitor
device.
Cause Measures
• Turn on the power.
• Set the setting to "YES".
• Connect properly.
• Turn the subwoofer's channel volume
level up.
• Set to STANDARD
Surround).
• Set to a mode other than "STEREO".
• Replace with new batteries.
• Move closer.
• Remove obstacle.
• Press the proper button.
• Insert batteries properly.
• Check the HDMI connection.
• Properly select HDMI signal input
source.
• The AVR-2307CI will not output video
signal unless the other equipment
supports HDCP.
• Check whether the output format of
the connected player
FORMAT) matches the supported
input format of connected monitor
equipments.
• Set the HDMI audio playback setting
at the "HDMI In Assignment"
settings to "AMP".
• Set the HDMI audio playback setting
at the "HDMI In Assignment"
settings to "TV".
Page Symptom
— Power has turned off
60 and the power indicator
is blinking red.
8, 23
36
(Dolby/DTS —
—
Sound is only produced
from the center speaker.
3
3
3
"DOLBY DIGITAL" is not
displayed.
—
3
"CHECK ANTENNA" is
19
displayed in the XM
mode.
53
"NO SIGNAL" is
displayed in the XM
19
mode.
"OFF AIR" is displayed
in the XM mode.
19
(HDMI
Receiving only XM
channels 0 and 1.
53
53
73
ENGLISH
Cause
• The set's internal temperature has • Put the AVR-2307CI in a well-
risen and the protection circuit has ventilated place.
been activated. • Turn off the power, then wait for the
set to fully cool off before turning the
power back on.
• The core wires of the speaker cables • Check the connections of all the
are touching each other or the AVR- speaker cables.
2307CI's rear panel, activating the
protection circuit.
• AVR-2307CI is malfunctioning. • Turn off the power and contact a
DENON customer service center.
• You are playing a monaural source • When playing monaural sources,
(TV, AM radio broadcast, etc.) in the select a surround mode other than
STANDARD (Dolby/DTS Surround) STANDARD (Dolby/DTS Surround)
mode. mode.
• DVD player's digital audio output • Check the DVD player's audio output
setting is not proper. setting.
For details, see the DVD player's

operating instructions.

• AVR-2307CI's XM connectors and the • Check that the connection are
XM Passport System is not properly correct.
connected.
• The signal cannot be received. • Reposition your XM Passport System.
• The selected channel is not currently • Select the another channel.
broadcasting.
• The XM Tuner is not activated. • Contact XM Radio.
Troubleshooting
Measures Page
8
8
8
8
35
—
22
39
39
38