Advertisement
C
M
ONSOLE
C
ONTROLLER
Installation Card For
Door Lock Kit
Read Instructions Completely Before
Beginning Installation Procedures
Printed on recycled paper
NOTICE
© 2001 Compaq Information Technologies Group, L.P.
Compaq and the Compaq logo are trademarks of Compaq Information Technologies
Group, L.P.
Compaq shall not be liable for technical or editorial errors or omissions contained herein.
The information in this document is provided as is without warranty of any kind and is
subject to change without notice. The warranties for Compaq products are set forth in the
express limited warranty statements accompanying such products. Nothing herein should
be construed as constituting an additional warranty.
Compaq Console Management Controller Door Lock Kit Installation Instructions
Second Edition (December 2001)
Part Number 240828-022
240828- 022
ANAGEMENT
About This Device
This document provides instructions to assist qualified personnel
with the installation of the Compaq Console Management
Controller (CMC) Door Lock Kit.
This door lock kit includes the following features:
I
Installs in the 9000 and 10000 series of Compaq racks.
Mounts in a 0U configuration.
I
I
Provides front and rear door locking control for a single rack.
Regulatory Compliance Information
This CMC Door Lock Kit is listed and certified for use only with
the Compaq Console Management Controller Units. This device
is not intended for use with nor suitable for connection to facility
burglary protection, security, or surveillance systems.
Regulatory certification for this product was obtained under
agency series number EO3009L. The corresponding part number
is 203039-B23.
Read Before Installing Product
Read the Important Safety Information guide (included with this
kit) before installing this product.
WARNING: There is a risk of personal injury from electrical shock and
hazardous energy levels. The installation of options and routine maintenance
and service of this product must be performed by individuals who are
knowledgeable about the procedures, precautions, and hazards associated
with AC power products.
Follow the instructions in this document during installation of the
door lock kit.
Kit Contents
Door lock control unit
I
- Mounting brackets (257661-001)
I
Country-specific power cord
Front rack door
I
- Lock assembly
- 91XX, 9842, and 106XX (257662-001)
- Latch assembly
- 91XX and 106XX (257662-002)
- 9842 (257662-003)
I
Rear rack door
- Lock assembly
- 91XX, 9842, and 106XX (257663-001)
- Latch assembly
- 91XX and 9842 (257663-002)
- 106XX (257663-003)
- Brackets
- Standard rack (257664-001)
- Standard rack with extension kit (257664-002)
I
Tie wraps
Cables
I
- Concealed Door Release cable assembly (257658-001)
- CMC lock command cable (231915-001)
2
- I
C communication cable (231526-002)
Software
I
- Compaq Intelligent Rack Manager Lite CD
- Power Products Documentation CD
Mounting hardware
I
- Screws
- Cage nuts
Advertisement
Table of Contents
Related Manuals for Compaq 203039-B21 - Console Management Controller
Summary of Contents for Compaq 203039-B21 - Console Management Controller
- Page 1 About This Device This document provides instructions to assist qualified personnel with the installation of the Compaq Console Management Controller (CMC) Door Lock Kit. This door lock kit includes the following features: ONSOLE ANAGEMENT Installs in the 9000 and 10000 series of Compaq racks. Mounts in a 0U configuration.
- Page 2 Connecting the Actuator Cable to the Lock Mechanism The actuator cables are attached to the door lock control unit. Use the short cable to connect to the front lock mechanism and the longer cable to connect to the rear lock mechanism. To connect to the front lock mechanism, feed the actuator cable 2 through the gap between the rack rail and frame.
- Page 3 91XX Series Rack with Extension Kit Installing the Front Door Lock Mechanism Align the extension brackets (257664-002) on the rear door lock mechanism and secure with the screws. Position the rear door lock Connect the front door lock assembly to the side of the front frame. assembly as shown, so that the assembly extends towards the rear door.
-
Page 4: Connecting The Power Cord
10000 Series Rack Set the address switch to 1 or 2 on the door lock control unit to match the lock port that is connected to the CMC. To accommodate the double doors of a 106XX rack, unbolt the locking mechanism from the crossbar and reposition in the left hole pair as shown 1. -
Page 5: Configuring The Software
Connecting to an Additional Rack Configuring the Software A single CMC can support up to two door lock kits. Repeat steps Configure the door lock control unit using the Compaq Intelligent 1 through 7 to complete installation of the door lock equipment for the Rack Manager Lite software (see the Compaq Console Manage- second rack. -
Page 6: Maintenance
Maintenance WARNING: To reduce the risk of injury from electric shock, remove the power cord before servicing. When the CMC indicates that the batteries in the door lock control unit require changing, remove the screws 1, lift the cover 2 off, and replace the six batteries with the same type and capacity (NiMH, size AA, 1100mAh) 3.
Need help?
Do you have a question about the 203039-B21 - Console Management Controller and is the answer not in the manual?
Questions and answers