Table of Contents
Advertisement
Installation
Instructions
Overthe Range
Microwave Oven
Questions ?Call 800.GE.CARES (800.432.2737) or Visit,,,,_x_ ebsite ;,t:Hotpointcom
I
BEFORE YOU BEGIN
Read
these
instructions
completely
and
carefully.
• IMPORTANT
- S_,,e t hese
instructions
for local
inspector's
use.
• IMPORTANT
- Obse_,'e _,ll
governing
codes
and
ordinances.
• Note
to Installer
-
Be sure
to leave
these
instructions
with the Consumer.
° Note to Consumer
- KeeI)
these
instructions
for future
reterence.
° Skill level - Installation
of this appliance
requires
basic mechanical
and
electrical
skills.
•
Proper
installation
is the
responsibility
of the
installer.
•
Product
tailure
due
to improper
installation
is not
coxered
under
the
_M_rrantx.
IIIIIIIIIIIIIIIIIIIIII
CZ]
I
For a Spanish versionof this manual, visitour Website at Hotpoint.com.
Para consultaruna versionen espa#ol de este manual de instrucciones,visite nuestrositio
de internet Hotpointcom.
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Advertisement
Table of Contents
Related Manuals for Hotpoint RVM1535DM1WW
Summarization of Contents
Important Safety Instructions
Electrical Safety Precautions
Take precautions like removing fuses and checking grounding to prevent electrical shock.
Receptacle and Circuit Checks
Ensure wall receptacles and circuits are checked by a qualified electrician.
Two-Prong Receptacle Replacement
Replace any two-prong receptacles with properly grounded three-prong ones.
Power Cord Handling Guidelines
Never cut, deform, or remove power cord prongs; avoid extension cords.
Mounting Surface Strength Requirements
Verify mounting surface can support the microwave and additional loads.
Installation Location Restrictions
Cannot install on islands/peninsulas; must mount to top cabinet and wall.
Two-Person Installation Recommendation
It is recommended that two people install the microwave for safety and ease.
Appliance Grounding for Safety
Proper grounding is essential to avoid severe or fatal electric shock.
Electrical Requirements for Microwave
Product Electrical Specifications
Microwave rated 120V AC, 60Hz, 15A, 1.58kW. Ensure correct voltage and frequency.
Wiring and Code Compliance
Wire size must conform to National and local electrical codes.
Branch Circuit and Outlet Specifications
Use a separate 15-20A branch circuit with a single grounded outlet.
Outlet Box Installation Location
The outlet box should be located in the cabinet above the microwave oven.
Qualified Electrician for Electrical Work
Outlet box and circuit must be installed by a qualified electrician per code.
Hood Exhaust Venting Options
Outside Top Exhaust Example
Example of one possible ductwork installation for venting exhaust upwards.
Outside Back Exhaust Example
Example of one possible ductwork installation for venting exhaust horizontally.
Handling Shipment and Installation Damage
Damage During Shipment Procedures
Return unit to store for repair/replacement if damaged during shipment.
Responsibility for Customer-Caused Damage
Customer is responsible for repair/replacement of units damaged by the customer.
Responsibility for Installer-Caused Damage
Installer is responsible for repair/replacement of units damaged by the installer.
Included Parts and Hardware
Hardware Packet Contents
Check the installation hardware packet for all included parts.
Additional Parts List
Verify all additional parts, such as templates and adapters, are present.
Mounting Plate Placement and Stud Finding
Removing Oven and Mounting Plate
Instructions for safely removing the microwave from packaging and detaching the mounting plate.
Locating Wall Studs for Mounting
Methods and tips for accurately finding wall studs for secure attachment.
Determining Wall Plate Location
Template Use for Flat Bottom Cabinets
Use the template to determine wall plate position for cabinets with flat bottoms.
Template Use for Recessed Bottom Cabinets
Use the template to determine wall plate position for cabinets with recessed bottoms.
Aligning Template with Cabinet Overhang
Align the template with the cabinet's front overhang for proper placement.
Ensuring Level Microwave Installation
Use a level to ensure the microwave is installed perfectly level.
Determining Rear Mounting Screw Locations
Safety: Wear Gloves During Handling
Wear gloves to protect hands from potential cuts from sharp edges.
Purpose of the Rear Wall Template
The Rear Wall Template aids in positioning the mounting plate and locating the exhaust outlet.
Achieving Accurate Template Positioning
Use a level to ensure the template is positioned accurately on the wall.
Locating and Marking Wall Studs
Mark at least one stud and consider stud spacing for screw locations.
Drilling Holes for Mounting Hardware
Drill holes according to template markings for screws and toggle bolts.
Important: Do Not Mount Plate Yet
Note that the mounting plate should not be attached to the wall at this stage.
Choosing Your Installation Type
A. Outside Top Exhaust (Vertical Duct)
Install for venting exhaust vertically through a duct to the outside.
B. Outside Back Exhaust (Horizontal Duct)
Install for venting exhaust horizontally through a duct to the outside.
C. Recirculating (Non-Vented Ductless)
Install for recirculating air within the room without external venting.
Outside Top Exhaust Installation
Installation Overview for Top Exhaust
Summary of the steps required for installing the top exhaust ventilation.
Attach Mounting Plate to Wall
Secure the mounting plate to the wall using provided hardware and ensuring it's level.
Outside Back Exhaust Installation
Installation Overview for Back Exhaust
Summary of the steps required for installing the back exhaust ventilation.
Prepare Rear Wall for Back Exhaust
Cut the rear wall opening according to the template for back exhaust.
Recirculating Installation
Installation Overview for Recirculating
Summary of the steps required for recirculating air without external venting.
C1. Attach Mounting Plate to Wall
Secure the mounting plate to the wall using provided hardware.
C2. Prepare Top Cabinet for Recirculation
Use template to mark holes in the top cabinet for recirculation setup.
Final Checks Before Use
Confirm Installation Completion
Verify that all installation steps have been completed correctly.
Remove Packing Material
Ensure all packing materials are removed from the microwave interior.
Install Turntable and Ring
Place the turntable and support ring inside the microwave cavity.
Restore Power Supply
Turn the circuit breaker back on or replace the house fuse.
Connect to Dedicated Electrical Outlet
Plug the microwave's power cord into a dedicated 15-20 amp outlet.
Consult Owner's Manual
Refer to the Owner's Manual for additional information and operation.
Retain Installation Instructions Document
Keep these installation instructions for the local inspector's records.
Need help?
Do you have a question about the RVM1535DM1WW and is the answer not in the manual?
Questions and answers