Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Husqvarna 325HE4 Series
Summarization of Contents
KEY TO SYMBOLS
Symbols
Explanations of various symbols used in the operator's manual.
GENERAL SAFETY PRECAUTIONS
Personal protective equipment
Details required personal protective equipment for safe operation.
Machine's safety equipment
Details the machine's safety equipment and its checks.
Throttle lock
Explains the function and checks for the throttle lock.
Stop switch
Describes how to use and check the stop switch.
Hand guard
Details the hand guard's purpose and checks.
Vibration damping system
Explains the vibration damping system and its checks.
Muffler
Details the muffler's function, safety warnings, and maintenance.
Blades
Describes blade adjustment, sharpening, and replacement.
Blade guard
Details the blade guard's purpose and checks.
Gear housing
Warns about the hot gear housing during operation.
ASSEMBLY
Fitting the hand guard and loop handle
Step-by-step instructions for fitting the hand guard and loop handle.
Fitting the handle
Instructions for fitting the handle using screws.
Fitting the cutting head
Instructions for fitting the cutting head to the shaft.
Adjusting the harness
Guidance on putting on and adjusting the harness.
Fitting the impact guard
Instructions for fitting the impact guard and screw tightening.
FUEL HANDLING
Fuel safety
Safety precautions for handling fuel and preventing accidents.
Transport and storage
Guidelines for safely transporting and storing the machine and fuel.
Fuel
Details on fuel types, octane rating, and mixing ratio.
Two-stroke oil
Information on recommended two-stroke oil and mixing ratio.
Mixing
Instructions on how to mix gasoline and two-stroke oil correctly.
Fueling
Safety precautions to follow when refuelling the machine.
STARTING AND STOPPING
Check before starting
Pre-start checks to ensure safe operation and machine condition.
Starting and stopping
Detailed steps for starting and stopping the engine.
Cold engine
Procedure for starting a cold engine using the primer bulb.
Warm engine
Procedure for starting a warm engine using the primer bulb.
Starting
Instructions on how to pull the starter cord to start the engine.
Stopping
How to stop the engine using the stop switch.
WORKING TECHNIQUES
General working instructions
Basic safety precautions and advice for working with the hedge trimmer.
Safety instructions while working
Crucial safety tips to follow during operation.
Personal protection
Recommendations for personal protective equipment during use.
Safety instructions regarding the surroundings
Guidelines for ensuring the safety of people and the environment.
Safety instructions after completing work
Steps to take after finishing work, including safety measures.
Basic working techniques
Guidance on proper techniques for trimming hedges efficiently.
Changing the hedge trimmer angle
Instructions for adjusting the angle of the cutting unit.
Transport position
Instructions for folding the cutting unit for transport and storage.
MAINTENANCE
Carburetor
Details on carburetor function, adjustment, and settings.
Basic setting
Information on initial carburetor settings and factory adjustments.
Fine adjustment
Instructions for fine-tuning the carburetor for optimal performance.
Conditions
Factors to consider before adjusting the carburetor.
Low speed jet L
Procedure for adjusting the low speed jet (L-jet).
Fine adjustment of the idle speed T
How to adjust the idle speed using the T-screw.
High speed jet H
Procedure for adjusting the high speed jet (H-jet).
Correctly adjusted carburetor
Symptoms of a correctly adjusted carburetor.
Muffler
Details on muffler maintenance, spark arrestor mesh, and catalytic converters.
Cooling system
Explains the cooling system and how to clean it.
Spark plug
Information on spark plug condition, gap, and replacement.
Air filter
Details on air filter cleaning, replacement, and oiling.
Cleaning the air filter
Step-by-step guide to cleaning the air filter.
Oiling the air filter
Instructions for oiling the air filter for dusty conditions.
Gear housing
Instructions for greasing the gear housing.
Cleaning and lubrication
Cleaning blades and lubricating blade bars for storage.
Maintenance schedule
A schedule of daily, weekly, and monthly maintenance tasks.
FEDERAL EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS
Details owner responsibilities for warranty coverage.
MANUFACTURER'S WARRANTY COVERAGE
Explains the manufacturer's warranty coverage for emission parts.
OWNER'S WARRANTY RESPONSIBILITIES
Owner's duty to perform maintenance and avoid misuse.
WARRANTY COMMENCEMENT DATE
States when the warranty period begins.
LENGTH OF COVERAGE
Defines the warranty period for warranted parts.
WHAT IS COVERED
Details what parts and services are covered under warranty.
WARRANTY PERIOD
Specifies the duration for which parts are warranted.
DIAGNOSIS
Owner's rights regarding diagnostic labor costs.
CONSEQUENTIAL DAMAGES
Husqvarna's potential liability for damages caused by warranted part failure.
WHAT IS NOT COVERED
Lists conditions that void warranty coverage.
ADD-ON OR MODIFIED PARTS
States that modified parts can void the warranty.
HOW TO FILE A CLAIM
Instructions on how to contact for warranty questions.
WHERE TO GET WARRANTY SERVICE
Information on authorized service locations.
MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS
Details on warranty coverage for emission-related parts maintenance.
EMISSION CONTROL WARRANTY PARTS LIST
Lists parts covered under the emission control warranty.
MAINTENANCE STATEMENT
Owner's responsibility for performing required maintenance.
Need help?
Do you have a question about the 325HE4 Series and is the answer not in the manual?
Questions and answers