Advertisement
3
1
2
7
8
5
6
11
10
12
14
15
18
17
2193250-04.indd 5-8
Accessories
14
Press the On/Off button with the foot to start the
vacuum cleaner.
1
Dustbag
15
Suction power setting: using the suction control on
2*
Telescopic tube / Extension tube
the vacuum cleaner. In order to conserve energy
3
Hose handle
of your cleaner we suggest running the cleaner at
4
Carpet/hard floor nozzle
OPTIMUM. However, it is possible to turn the power
5*
Parquet nozzle
control past OPTIMUM to boost the power level in
4
6*
Turbo nozzle
order to get maximal dust removal („Click" sound
indicates leaving the optimum area).
7*
Crevice nozzle
16
A practical parking feature (as well as minimizing the
8*
Upholstery nozzle
risk of backache) makes things easier when pausing
Safety precautions
during cleaning.
17
The parking feature makes it easier to move and store
Powerboost should only be used by adults and
the vacuum cleaner.
only for normal vacuuming in a domestic
environment. The vacuum cleaner features
Use the nozzles as follows:
double insulation and does not need to be earthed.
Carpets: Use the carpet/hard floor nozzle with the lever in
Never vacuum:
position (18). Reduce suction power for small carpets.
•
In wet areas.
Hard floors: Use the carpet/hard floor nozzle wit the lever in
•
Close to flammable gases, etc.
position (19).
•
Without a dustbag (this may damage the
Wooden floors: Use the parquet nozzle (certain models
9
cleaner).
only, 5).
A safety device is fitted which prevents the cover
closing without a dustbag. Do not attempt to
Upholstered furniture: Use the upholstery nozzle (8).
force cover shut.
Crevices, corners, etc.: Use the crevice nozzle (7).
Never vacuum:
Using the turboz nozzle* (6).
•
Sharp objects.
20
Attach the nozzle to the tube.
•
Fluids (this can cause serious damage to the
machine).
Note: Do not use the turbo nozzle on fur rugs, rugs with long
•
Hot or cold cinders, lit cigarette butts, etc.
fringes or a pile depth exceeding 15 mm. To avoid damaging
•
Fine dust from plaster, concrete, flour or ash,
the carpet, do not keep the nozzle stationary whilst the brush is
for example. The above can cause serious damage
rotating. Do not pass the nozzle across electric cables, and be
to the motor – damage which is not covered by
sure to switch off the vacuum cleaner immediately after use.
13
the warranty.
Changing the Dust bag
Electrical cable precautions:
21
The dust bag must be replaced when the indicator
•
A damaged cable must be replaced by an authorised
window is completely red. Read the indicator with the
service centre. Damage to the cleaner cable will not be
floor nozzle lifted up from the carpet.
covered by the warranty.
22
Remove the hose and open the lid.
•
Never pull or lift the vacuum cleaner by the cable.
23
Pull the cardboard holder to remove the dust bag.
•
Disconnect the plug from the mains before
This automatically closes the dust bag and stops dust
cleaning or maintenance of the vacuum cleaner.
from leaking out.
•
Regularly check that the cable is not damaged.
24
Insert a new dust bag by pushing the cardboard
Never use the vacuum cleaner if the cable is damaged.
holder straight down in its tracks. Close the lid.
All service and repairs must be carried out by an authorised
service centre. Always keep the vacuum cleaner in a dry place.
Before starting
9
Check that the dustbag and motor filter are in
16
place.
10
Insert the hose until the catch clicks to engage (press
the catch to release the hose).
11
Attach the extension wand or telescopic wand (only
on certain models) to the hose handle and floor
nozzle (to take them apart again, twist and pull).
12
Extend the cord and plug it into the wall socket. The
vacuum cleaner has an integrated cord winder.
13
Press the foot pedal to rewind the cable (take hold of
the plug to prevent it striking you).
* Certain models only
19
Changing the filters
Troubleshooting
The vacuum cleaner does not start
The more often the better for the efficiency of the cleaner.
Should be done with every 3 months of the dust bag.
1
Check that the cable is connected to the mains.
The filters must always be replaced with new ones and
2
Check that the plug and cable are not damaged.
cannot be washed.
3
Check for a blown fuse.
Replacing of motor filter ( HEPA filter* / Microfilter* )
The vacuum cleaner stops
1
Check whether the dust bag is full. If so, replace it with
22
Depress the catch and open the lid.
a new one.
25
- Remove the old filter
2
Is the nozzle, tube or hose blocked?
- Insert a new filter and close the lid.
3
Are the filters blocked?
Replacement of the exhaust filter ( Microfilter )
Water has entered the vacuum cleaner
26
Open the filter's lid and fold up, remove the dirty filter
It will be necessary to replace the motor at an authorised
27
Insert a new filter and close back the lid.
service centre. Damage to the motor caused by the
Cleaning the hose and nozzle
penetration of water is not covered by the warranty.
The vacuum cleaner stops automatically if the nozzle, tube,
Consumer information
hose or filters and dust bag becomes blocked. In such
cases, disconnect from mains and allow to cool for up to 60
Electrolux declines all responsibility for all damages arising
minutes. Clear blockage and/or replace filters and dust bag
from any improper use of the appliance or in cases of
and restart.
tampering with the appliance.
This product is designed with the environment in mind. All
Cleaning tubes and hoses
plastic parts are marked for recycling purposes.
28
Use a cleaning strip or similar to clear the tubes and
hose.
For more informations visit our web site:
29
It may also be possible to remove the obstruction in
www.electrolux.co.uk
the hose by squeezing it. However, be careful in case
the obstruction is caused by glass or needles caught
inside the hose.
Note: The warranty does not cover any damage to the hose
caused by cleaning it.
Cleaning the floor nozzle
30
To avoid deterioration of suction power, frequently
clean the carpet/hard floor nozzle. The easiest way to
clean it is by using the hose handle.
Cleaning the turbo nozzle*
31
Disconnect the nozzle from the vacuum cleaner tube
and remove entangled threads, etc. by snipping them
away with scissors. Use the hose handle to clean the
nozzle.
32
In case the turbo nozzle stops working, open the
cleaning lid and remove any objects that obstructs the
turbine to rotate freely.
* Certain models only
22
21
20
25
23
24
26
27
28
30
29
32
31
7/11/07 5:47:52 PM
Advertisement
