Table of Contents
Advertisement
L4630BA(EN).fm Page 7 Thursday, June 15, 2006 3:42 PM
OPERATIONS
Watching a TV Programme
1)
STANDBY-ON
Press
to turn on the TV.
2)
Select the desired channel with
buttons
.
• Enter a channel numbers as a two-digit number within 2.5
seconds for the quickest results. For example, to select channel
0
6
6, press
and
. If you only press
after 2.5 seconds.
• You can only select channels 1–99.
3)
Adjust the volume to the desired listening level using
VOL. +/-
on the front panel or
control.
• If you want to mute the sound temporarily (e.g. during a
(mute)
telephone call), press
(mute)
you press
again, the sound will return at its original
volume level.
4)
Adjust picture controls for a natural looking image.
(See "Picture Adjustment".)
External Input Mode
• To use the RGB scart jack for connecting a device, select "AV1".
• To use the AUDIO/VIDEO input jacks, select "AV2".
Using INPUT SELECT
INPUT SELECT
Press
to select "AV1" or "AV2" mode.
Using the Number buttons
0
0
1
the Number buttons
Press
,
,
with
the TV screen.
0
0
2
the Number buttons
Press
,
,
with
the TV screen.
Note: •
When you use the S-VIDEO connection, S-VIDEO jack is
given priority over the VIDEO jack.
TV Colour System Change
Different countries use different television colour systems. You can
COLOR SYSTEM
change the system by pressing
When you select AUTO by pressing
distinguish the system automatically according to the input signal
from the tuner or external devices.
If the picture on the TV screen is black and white, select the system
COLOR SYSTEM
manually by using
SYSTEM
, TV screen will change as follows.
for tuner input (TV):
AUTO or PAL
for external input (VIDEO):
AUTO, PAL, NTSC3.58 or NTSC4.43
Teletext Reception
Many TV channels transmit Teletext information along with their TV
channels. With this unit, you can retrieve and display it on the screen
using the built-in Teletext decoder.
1)
(text)
Press
to switch the Teletext decoder on. Your unit
now shows Teletext for the TV channel you have selected. Press
(text)
again to show Teletext in transparent mode.
2)
If you want to select another page, type in the number of the
the Number buttons
page with
Note: •
EXPAND
To enlarge fonts, press
•
To select Teletext subpages, press
•
To directly select the page numbers shown at the bottom of
RED/GREEN/YELLOW/CYAN
the TV screen, use
•
To call up the hidden information, press
•
To hold the current page, press
•
To go back to the start page, press
3)
(text)
Press
to switch the Teletext decoder off.
/
(prog.)
the Number
or
6
, channel 6 will be selected
+/- (vol.)
on the remote
on the remote control. When
, so that "AV1" appears on
, so that "AV2" appears on
.
COLOR SYSTEM
, this unit will
COLOR
. Each time you press
.
.
SUB CODE
.
.
REVEAL
.
(hold)
.
(index)
.
7
Setting the Sleep Timer
The sleep timer function allows you to have the power automatically
turn off after a set time period.
1)
STANDBY-ON
Press
to turn on the TV and press
remote control.
2)
You may change the sleep time by pressing
control repeatedly. The timer can be set up to 90 minutes. Each
SLEEP
time
is pressed the time increases by 30 minutes. (The
timer display counts up and sleep timer will be displayed on the
SLEEP
screen when you press
on the remote control.)
Note: •
When you disconnect the unit from the AC outlet or when
you have a power failure, the sleep time will be lost.
To Cancel the Sleep Timer
SLEEP
Press
repeatedly until "0" is displayed.
Picture Adjustment
The picture can be adjusted according to your personal preferences.
These settings are automatically stored after exiting the picture menu.
1)
SETUP
Press
so that the menu display appears on the TV screen.
2)
Cursor
Press
K / L to point to "PICTURE", then press
ENTER
.
3)
Cursor
Press
K / L to select an item you want to adjust, then
ENTER
press
.
• The selected item will be indicated by yellow.
4)
Cursor s
Press
/
to adjust the level, then press
B
SETUP
PICTURE
BACK LIGHT [BRIGHT]
INITIAL
5)
SETUP
Press
to exit.
Cursor s
to decrease
BRIGHTNESS
brightness
CONTRAST
to decrease contrast to increase contrast
COLOUR
to pale
SHARPNESS
to soft
TINT
to purple
"TINT" appears only when receiving NTSC signals from an
additional device connected by either RGB scart jack or AUDIO/
VIDEO input jacks.
Note: •
In the above steps, the picture adjustment display will
disappear from the TV screen automatically after about 60
seconds if you do not press any buttons. Press
ENTER
so that "PICTURE" is selected.
Back Light Selection
1)
SETUP
Press
so that the menu display appears on the TV screen.
Cursor
2)
Press
K / L to point to "BACK LIGHT".
3)
ENTER
Press
to select the mode you wish.
4)
SETUP
When done, press
to exit.
SETUP
SETUP
PICTURE
PICTURE
BACK LIGHT [BRIGHT]
BACK LIGHT [NORMAL]
INITIAL
INITIAL
Status Display
To check the Channel number & Audio mode, press
DISPLAY
time you press
, TV screen will change as illustrated:
the Number buttons
When you select the channel using
desired channel (position number).
<CHANNEL NUMBER and AUDIO MODE>
<OFF>
Press once
SLEEP
on the
SLEEP
on the remote
ENTER
.
PICTURE
_
+
BRIGHTNESS
_
+
CONTRAST
_
+
COLOUR
_
+
SHARPNESS
_
+
TINT
Cursor B
to increase
brightness
to brilliant
to clear
to green
SETUP
and
SETUP
PICTURE
BACK LIGHT [DARK]
INITIAL
DISPLAY
. Each
, select the
P08
STEREO
EN
Advertisement
Table of Contents
