1. Manuals
  2. Brands
  3. KuWFi Manuals
  4. Network Router
  5. C160
  6. User manual

KuWFi C160 User Manual

5g router with sim card slot
Hide thumbs Also See for C160:
Table of Contents

Advertisement

Quick Links

Download this manual
KuWFi 5G Router with sim card Slot
C160 User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the C160 and is the answer not in the manual?

Questions and answers

Related Manuals for KuWFi C160

Summary of Contents for KuWFi C160

  • Page 1 KuWFi 5G Router with sim card Slot C160 User Manual...
  • Page 2 Router body Introduction...

  • Page 3: Install Sim Card

    1 Setup CPE For more detail about installation please refer to Quick start Guide. 1.1 Install SIM Card 1. Make sure you use the correct SIM card: Nano- SIM (4FF). 2. Insert the SIM card gently into the SIM card slot in the direction shown in the figure below until it clicks.
  • Page 4 Connect the power adapter to the 5G CPE. Press the power button to turn on the device, 5G CPE will initialize start up process. When the indicator stop flashing, the 5G CPE complete the initialization and start to work.

  • Page 5: Login Web Gui

    2 Login WEB GUI 2.1 Login To login Web GUI, please follow below steps: Connect the device to laptop either over Ethernet cable or Wi-Fi. Open browser and input 192.168.8.1 or http://my.5g.device/. Input username & password (admin/admin). 2.2 Web Instruction 2.2.1 Home page After login Web GUI then will jump to home page.

  • Page 6: Wi-Fi Settings Page

    2.2.2 User list page It will show current user information. You can enable black list or white list in MAC filter mode page, and add/delete forbidden/allow user. 2.2.3 Wi-Fi Settings page You can change Wi-Fi parameters, such as Wi-Fi band, Wi-Fi SSID, Wi-Fi Key, channel, channel bandwidth...
  • Page 7 and so on.
  • Page 8 2.2.4 APP module page It's a guidance page, user can check device status and configure device settings from the items of this page.
  • Page 9 2.2.5 Status page Login Web GUI, then go to APP MODULE > Status page, we can get the device connection status, WAN IP, DNS, boot time..from this page.

  • Page 10: Change Login Password

    2.3 Change login password To change login password, please follow below steps: 1. Go to APP MODULE -> Admin Settings.
  • Page 11 2. Input the new password and confirm, then click “Apply” to take effect.

  • Page 12: Network Settings

    2.4 Network settings 2.4.1 Network Mode Device allows user to change network mode, such as 5G-SA, 5G-NSA, 4G only, 3G only. To change network mode, please follow below steps: Go to APP MODULE -> Network Settings.
  • Page 13 Select the network mode from drop down list.

  • Page 14: Apn Settings

    2.4.2 APN settings To change APN manually, please follow below steps: Go to APP MODULE -> Network Settings. Change profile mode to manual, then input APN or other parameters which you are needed. Click “Apply” to take effect. If you want to set more different APN, you can select from APN list and fill in...

  • Page 15: Wan Settings

    parameters. 2.5 WAN settings If you want to use WAN cable/PPPoE/WiFi Extender, you can go to APP Module -> WAN settings to select WAN type from drop-down list.
  • Page 16 CPE also support secondary WAN type, mobile ping also should be enabled. When main WAN type has no network service, device will switch to secondary WAN type automatically. If WAN type has network service, device will switch back to main WAN type automatically.
  • Page 17 2.6 Position recommend Please login Web UI, go to APP Module -> use position recommend function for helping you to decide location selection. Measure the signal at some position, recommend the best.

  • Page 18: Firmware Upgrading

    3 Firmware Upgrading There are 2 methods to upgrade the device: 1. FOTA – To upgrade the device over the air. Please keep the device power on and ensure it has internet connectivity. 2. Local Upgrade – To upgrade the firmware that downloaded to local. 3.1 Preparation for FOTA Please share below information of the device to us for enabling the FOTA: 1.

  • Page 19: Local Upgrade

    3.2 Local Upgrade Firstly, please get the upgrading package or image file from us. 1. Login to Webui.
  • Page 20 2. Go to APP MODULE -> Update page. 3. Choose Firmware Management -> Select File -> choose firmware package -> Click Apply button.
  • Page 21 4. Device will download the upgrade file from your PC and install it automatically. 5. After installation completed, device reboots automatically.
  • Page 23 4 Login to the engineering page Basic 3 steps of login engineering page: 1. Connect the device to laptop. 2. Open browser and enter http://my.5g.device/engineering.html. 3. Input engineering page username & password (superadmin/superadmin).

This manual is also suitable for:

Sa c160-l

Table of Contents