Hunter 59214 Manual

52 inch ocala noble bronze indoor / outdoor ceiling fan with led light kit and pull chain

Advertisement

Table of Contents
Congratulations on purchasing
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or office for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
To register your fan, please visit:
www.HunterFan.com/register
Save your receipt for proof of purchase.
What to Expect with
Your Installation
Tools Needed
30 inches
7 feet
2
Downrod
6
Light Kit
1
M3604-01 • 03/21/16 • © 2016 Hunter Fan Company
Mounting Options
Ladder
3
Wiring
Canopy
9
Operation,
Maintenance & Cleaning
12
www.HunterFan.com
1.888.830.1326
Ceiling Bracket
4
5
Blades
10
11
Troubleshooting
?
?
?
15
16

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 59214 and is the answer not in the manual?

Questions and answers

Summary of Contents for Hunter 59214

  • Page 1 To register your fan, please visit: www.HunterFan.com/register Save your receipt for proof of purchase. Operation, Light Kit Maintenance & Cleaning Troubleshooting M3604-01 • 03/21/16 • © 2016 Hunter Fan Company...
  • Page 2: What To Expect With Your Installation

    Assess ceiling angle Select a downrod length harmful interference to radio communications. M3604-01 • 03/21/16 • © 2016 Hunter Fan Company...
  • Page 3: Tools Needed

    The symbols can be used to identify Power Drill 9/64” Drill Bit the appropriate hardware for each step. Screwdrivers (optional) (optional) If mounting to a support structure, you will also need these tools. M3604-01 • 03/21/16 • © 2016 Hunter Fan Company...
  • Page 4: Mounting Options

    You need BOTH You need ONLY a Longer a Longer Downrod & Downrod an Angled Mounting Kit *most common M3604-01 • 03/21/16 • © 2016 Hunter Fan Company...
  • Page 5: Ceiling Bracket

    To avoid possible electrical shock, before 1-888-830-1326. installing your fan, disconnect the power by turning off the circuit breakers to the outlet Refer to warning w.1 on pg. 2 box associated with the wall switch location. M3604-01 • 03/21/16 • © 2016 Hunter Fan Company...
  • Page 6 Steps 1-5 to remove standard downrod pipe Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling Steps 6-10 to reassemble with new pipe M3604-01 • 03/21/16 • © 2016 Hunter Fan Company...
  • Page 7 4-5 full turns) until it stops. with pliers. DO NOT can be inserted. from the top of the downrod. HAND TIGHTEN. 8” 3/8” If the setscrew is not tightened securely, the fan may fall. M3604-01 • 03/21/16 • © 2016 Hunter Fan Company...
  • Page 8 Put the wires and downrod through the canopy. Let the canopy sit loosely on top CANOPY OR WIRES. Place the downrod of the fan. ball into the slot in the ceiling bracket. M3604-01 • 03/21/16 • © 2016 Hunter Fan Company...
  • Page 9 Spread the wires apart, with the grounded wires on one side of Refer to CAUTION c.1 on pg. 2 the outlet box and the ungrounded wires on the other side of the outlet box. M3604-01 • 03/21/16 • © 2016 Hunter Fan Company...
  • Page 10 Lift the canopy into place so that Insert the two canopy screws lifted into place, the canopy fits into the screw holes are aligned. found in the hardware bag. the hanging bracket as shown. M3604-01 • 03/21/16 • © 2016 Hunter Fan Company...
  • Page 11 M3604-01 • 03/21/16 • © 2016 Hunter Fan Company...
  • Page 12: Light Kit

    Failure to properly secure all 3 assembly screws could result in the switch secure all 3 assembly screws could result in the switch housing fixture falling. housing fixture falling. M3604-01 • 03/21/16 • © 2016 Hunter Fan Company...
  • Page 13 Make sure the light kit assembly is securely attached to the motor housing. Failure to properly secure all three assembly screws could result in the light fixture falling. M3604-01 • 03/21/16 • © 2016 Hunter Fan Company...
  • Page 14 The fan pull chain controls the speed: from high to off. The light pull chain controls the light fixture: on and off. M3604-01 • 03/21/16 • © 2016 Hunter Fan Company...
  • Page 15 When cleaning the fan, use soft brushes reverse switch to the opposite position. You or cloths to prevent scratching. Cleaning will need to remove the light cage and glass products may damage the finishes. to do so. M3604-01 • 03/21/16 • © 2016 Hunter Fan Company...
  • Page 16: Troubleshooting

    • Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram on page 9. • Check the plug connection in the switch housing. M3604-01 • 03/21/16 • © 2016 Hunter Fan Company...

Table of Contents