BreathableBaby 25507 Installation

PACKAGE INCLUDES:
hook & loop
(1) Short Panel:
fasteners
82 in. X 11 in. (208 X 28 cm.)
(1) Long Panel:
111 in. X 11 in. (282 X 28 cm.)
Four-Sided Slatted Crib
START HERE - Figure 1: Installing Long Panel
a
I
b
Figure 1 - Position Long Panel in Crib
(Top View of Crib)
e
III
Step 1. Properly position Long Panel along INSIDE, BACK of crib
1. Long Panel covers slats at BACK and SIDES of crib as shown above.
2. Make sure ties face UPWARDS and are OUTSIDE the crib.
Figure 2: Weaving Long Panel Around BACK Corner Posts (Inside View of Crib)
I
e
a
b
left end
Step 2. Covering Back Left (
1. Take left end of liner and weave BEHIND the crib slat (a),
2. then in FRONT of the back corner post (
3. Repeat for right side (c and d).
Figure 3: Securing Ends of Long Panel (Outside View of Crib)
IV
Step 3. Securing ends of Long Panel (refer to Figure 1 and 3)
1. Wrap and secure fasteners of right side of liner BEHIND crib slat (f)
on the crib short side.
2. Repeat for left side (e) crib slat.
3. To prevent sagging, pull liner tight at both ends for a snug t.
Solid Back Crib
Step 1. Properly position Long Panel along INSIDE, FRONT of crib
1. Long Panel covers slats at the FRONT and SIDES of crib as
shown in Figure 8. You will not use the Short Panel.
2. Make sure ties face UPWARDS and are OUTSIDE the crib.
3. Follow Figure 2 and Figure 3 for weaving through slats
and attaching ends of Long Panel to outside of crib.
Installation for Mesh Crib Liner
Fits Four-Sided Slatted & Solid Back Cribs
Contents: 100% Polyester
Easy Care: For best results, Machine wash warm,
gentle cycle. Wash separately or with like colors. Only
non-chlorine bleach when needed. Tumble dry low.
SECURE ALL FABRIC FASTENERS BEFORE
LAUNDERING TO AVOID SNAGGING.
BreathableBaby, LLC
2841 Hedberg Drive, Minnetonka, MN 55305.
©2016 BreathableBaby, LLC. MADE IN CHINA.
Customer Service: 1-877-827-4442
c
II
back
d
f
IV
II
c
d
right end
) and Right ( ) corner posts
I II
) and BEHIND crib slat (b).
I
(Right, Short Side View)
f
I
g
e
III
Step 1. Properly position Short Panel along INSIDE, FRONT of crib
1. Short Panel covers slats at FRONT of crib as shown above.
2. Make sure ties face UPWARDS and are OUTSIDE the crib.
Figure 5: Weaving Short Panel Around FRONT Corner Posts (Outside View of Crib)
f
Step 2. Covering Front Right (
ke right end of the liner and weave BEHIND crib slat (j),
2. then in FRONT of corner post (
3. Repeat for left side corner post (
Figure 6: Securing Ends of Short Panel (Outside View of Crib)
IV
j
Step 3. Securing ends of Short Panel (refer to Figure 4 and 6)
1. Wrap and secure fasteners of right side of liner BEHIND crib slat (i)
on the crib short side.
2. Repeat for left side (g) crib slat.
3. To prevent sagging, pull liner tight at both ends for a snug t.
I
solid back crib
b
Figure 8 - Position Long Panel in Crib
(Top View of Crib)
e
front
h
III
WARNING:
TO REDUCE THE RISK OF SUFFOCATION,
KEEP TOP OF LINER UP AND IN POSITION. DO NOT ALLOW LINER TO
SAG DOWN OR IN TOWARD THE SLEEPING SURFACE. DO NOT USE
LINER IF SAGGING CANNOT BE CORRECTED. TO PREVENT
ENTANGLEMENT OR STRANGULATION, POSITION TIES TO OUTSIDE OF
CRIB AND BE SURE THEY ARE SECURE. REMOVE LINER WHEN CHILD
CAN SIT UP UNAIDED OR CAN PULL TO A STANDING POSITION.
Figure 4: Installing Short Panel
Figure 4 - Position Short Panel in Crib
(Top View of Crib)
front
h
IV
(Right, Short Side View)
j
f
) and Left ( ) corner posts
IV III
) and nish BEHIND crib slat (f).
IV
).
III
(Right, Short Side View) Figure 7 - FRONT
(Outside View of Crib)
i
h
II
Figure 8 - FRONT
d
h
f
j
IV
II
i
f
j
IV
j
(Outside View of Crib)
j
Revised: March 2016