Universal Remote Control Easy Clicker UR3-SR Operating Manual

1 Introduction
Operating Manual
This remote control is designed to operate
most digital and analog cable boxes, as well
For Easy Clicker
as TVs, and a VCR or DVD player.
2

Installing Batteries

UR3-SR
Before you program or operate the remote
control, you must install two new AAA alkaline
batteries.
STEP1 Remove the battery compartment cover
from the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment
cover.
AAA alkaline batteries
4 Programming the Remote Control.
*Note : In this section, when you are
instructed to press a [DEVICE]
button, that means you should press
either the CBL, TV, or VCR button,
depending on which device you are
programming the remote to operate.
A. Manual Programming
The remote control can be programmed by
entering a three-digit code number that
Universal Remote Control, Inc.
corresponds to particular brands and models
of equipment. The three-digit code numbers
www.universalremote.com
are listed in the code tables sections of this
OCE-0009A Rev 05 (08/05/04)
instruction manual.
3 Button Functions
Install two
as shown here
STEP1 Turn on the equipment that you want the remote control to operate (Cable Box, TV, VCR,
or DVD).
STEP2 Press the [DEVICE] button and the [SELECT/OK] button simultaneously for three seconds.
The corresponding device LED will turn on indicating that it is ready to be programmed.
The LED will remain on for 20 seconds. The next step must be entered while the LED is on.
STEP3 Point the remote control toward the equipment and enter the three-digit code number
assigned to your brand from the code tables. If there are more than one three-digit
number listed for your brand, try one code number at a time until your equipment turns off.
*Note : You can verify that you have selected the correct code by pressing the [MUTE] button. The
equipment should turn on or off.
STEP4 Store the three-digit code by pressing the same [DEVICE] button once again. The device
LED will blink twice to confirm that the code has been stored.
*Note : Try all the functions on the remote
D. Programming a Second TV to the
control. If any of the functions do not
VCR Button
operate as they should, repeat the
instructions from Step 2 using the next
STEP1 Press the [VCR] button and the
three-digit code number from the same
[SELECT/OK] button simultaneously
brand list.
for 3 seconds. The VCR LED will
B. Auto Search Method
turn on for 20 seconds. The next
step must be performed while the
If none of the three digit code numbers
LED is on.
assigned to your brand of equipment works, or
the code table does not list your brand, you
STEP2 Press the [TV] button.
can use the Auto Search Method to find the
STEP3 Point the remote control toward the
correct three-digit code number for your
TV and enter the three-digit code
equipment by following steps:
for your TV from the TV codes
STEP1 Turn on the equipment that you want
table.
the remote control to operate (Cable
STEP4 Store the three-digit code by
Box, TV, VCR, or DVD).
pressing the [VCR] button. The device
STEP2 Press the [DEVICE] button and the
LED will blink twice to confirm that
[SELECT/OK] button simultaneously
the code has been stored.
for three seconds. The device LED
will turn on indicating that it is ready
E. Programming for Advanced
to be programmed. The LED will
Functions.
remain on for 20 seconds. The next
step must be entered while the LED is
on. In the CABLE device mode, the A,B,C and
blank macro buttons can be programmed to
STEP3 Point the remote control toward the
act as macro buttons to send out up to 10
equipment and alternately press the
commands with one button press. In this
[CH+] (or [CH-]) button and the
section, when you're instructed to press a
[MUTE] button. If the right code
[MACRO] button, you need to press either
number is sent, the equipment will
the A, B, C or blank macro button
turn off.
(depending on which button you are
*Note : You can verify that you selected the attempting to program).
correct code by pressing the [MUTE]
*Note : The A, B, and C buttons are not
button again. The equipment should
programmable if you have a digital
turn On or Off.
cable box made by Pace, Pioneer,
STEP4 Press the same [DEVICE] button to
or Scientific-Atlanta cable box.
store the code. The Device LED will
blink twice to confirm that the code STEP1 Press the [CBL] button to select the
has been stored.
CABLE mode.
C. To find the Three-Digit Code that STEP2 Press a [MACRO] button and the
[SELECT/OK] button simultaneously
Was Programmed using the
for 3 seconds. The CBL device LED
Auto Search Method
will turn on for 20 seconds. The
STEP1 Press the appropriate [DEVICE] next step must be performed while
button and the [SELECT/OK] button the LED is on.
simultaneously for three seconds.
STEP3 Press up to 10 buttons you wish to
The device LED will turn on for 20
store. The CBL device LED will blink
seconds. The next step must be
once for each command entered.
performed while the LED is on.
STEP4 Press the [CH+] button to store the
STEP2 Press the [INFO] button. The device
functions that are selected. The
LED will blink a number of times
indicating the number of each digit CBL device LED will blink twice to
for the code. Each digit is separated confirm the storage of functions.
by a one second interval of the LED
being off.
To erase the Macro programming and return
Example : One blink, then three blinks, then
to the original function:
eight blinks indicates the code
number 138.
STEP1 Press the [CBL] button to select the
CABLE mode.
*Note : Ten blinks indicates the number 0.
STEP2 Press a [MACRO] button and the
[SELECT/OK] button simultaneously
for 3 seconds. The CBL device LED
will turn on for 20 seconds. The next
step must be performed while the
LED is on.
STEP3 Press the [CH+] button to erase the
functions stored in the button. The
CBL device LED will blink twice to
confirm that the memory button has
been erased.
F. Assigning the Volume and Mute
keys to a Different Device
By default, the volume and mute keys operate
volume and mute functions on the TV. If you
would like those keys to operate those
functions on a different device, follow these
steps.
STEP1 Press the [SELECT/OK] button and
[CBL] button simultaneously for
three seconds. The device LED will
turn on for 20 seconds. The next step
must be performed while the LED is
on.
STEP2 Press the [VOL +] button. The device
LED will blink.
STEP3 Press the [DEVICE] button
corresponding to the device that you
would like the volume and mute
buttons to control. The device LED
will blink twice to confirm the
programming.
Example : If you wish to have the volume and
mute keys operate your cable box,
press the [CBL] button in Step3.
G. Assigning the Channel keys to a
Different Device
By default, the CH UP, CH Down, Numeric
buttons, and LAST keys operate through your
Cable Box. If you would like those keys to
operate those functions on a different device,
follow these steps.
STEP1 Press the [SELECT/OK] button and
[CBL] button simultaneously for
three seconds. The device LED will
turn on for 20 seconds. The next step
must be performed while the LED is
on.
STEP2 Press the [VOL -] button. The device
LED will blink.
STEP3 Press the [TV] button. The device
LED will blink twice to confirm the
programming.
*Note : If you wish to have the channel keys
operate your Cable box, press the
[CBL] button instead of the [TV]
button in Step 3.