Universal Remote Control UR3-J22TWM Operating Instructions

Operating Instructions
Introduction
1
For 3 Function
The remote control is designed to operate
the Motorola CFT2200 set top box and the
Cable Remote Control
majority of TV and VCR/DVD equipment on
the market.
UR3-J22TWM
Replacing Batteries
2
Before you program or operate the remote
control, you must install two new AAA
alkaline batteries.
STEP1 Remove the battery compartment
cover on the back of your remote
control.
STEP2 Check battery polarity carefully,
and install the batteries as shown
below.
STEP3 Replace the battery compartment
cover.
AAA alkaline batteries
Operations
4
Default State :
Device Default: Motorola CFT2200
Volume Default : TV volume and mute
through the TV, with the option of
controlling volume and mute through the
Cable Converter. Refer to Section E for
Universal Remote Control, Inc.
programming the volume and mute through
www.universalremote.com
your Cable Converter.
OEE-0035N Rev 07 (07/09/04)
Button Functions
3
indicates remote control activity
allow direct access to
specific channels and
menu options
displays help for on-screen
display screens
recalls the last channel that was
viewed
switches between cable TV and
Music Choice TM
displays the quick function screen
exits the on-screen display menus
displays the main on-screen display
menu
Install two
as shown here
pages through on-screen menu and
program guide screens
initiates VCR recording through the
on-screen menu (if so equipped)
Programming the Remote Control.
5
A. Three-Digit Code Programming Method.
The remote control can be programmed by pressing in a three digit code number that
corresponds to particular manufacturers and brands of Audio/Video equipment.
The three-digit code numbers are listed in the code table of the instruction manual.
STEP1 Turn on the equipment you wish to program. (TV, VCR, or DVD)
STEP2 Press the [DEVICE] button (TV POWER or VCR POWER) to be programmed and the
[SEL] button simultaneously for 3 seconds. The LED will turn on indicating the unit is
ready to be programmed.
*Tip : The LED will stay lit for 20 seconds. The next step must be entered while the LED is on.
STEP3 Point the remote control toward the equipment and enter the three-digit code number
assigned to your brand from the code tables.
*Tip : The equipment will turn off when the
correct three-digit code number has
been entered. You can verify you
have selected the correct code by
pressing the [MUTE] button, the
equipment should turn on or turn off.
*Note : If there is more than one three-digit
number listed for your brand, try
one code number at a time until
allow you to turn on and off your TV,
VCR, and CABLE box. They are also used to setup the
your equipment turns off.
remote control
changes the channel up and down
STEP4 Store the three-digit code number
by pressing the same [DEVICE]
turns the volume up and down
button once again. The LED will
INFO future use
blink twice to confirm that the code
FAV has been stored.
cycles through your favorite channels
MUTE turns volume off
*Note : Try all the functions on the remote
future use
control. If any of the functions do
MOVIES future use
not work as they should, repeat from
INFO
displays channel and program information Step 2 using the next three-digit code
C A B L E
number from the same brand list.
GUIDE displays the program guide
CURSOR KEYS navigate through on-screen guides
B. Auto Search Method.
SEL SEL
selects options from the program guide and
be used to set up the remote.
If the three-digit code numbers assigned to
your brand do not turn off your equipment or
DAY +/- moves the program guide one day
forward and backward
the code tables do not list your brand, you
can use the Auto Search Method to find the
TV/VCR
switches between control of
your TV and your VCR
correct three-digit code number for your
VCR/DVD KEYS perform standard VCR and DVD
equipment by the following steps:
functions when in VCR mode.
STEP1 Turn on the equipment you wish
to operate.
STEP2 Press the [DEVICE] button (TV
POWER or VCR POWER) to be
programmed and the [SEL] button
simultaneously for 3 seconds. The
LED will turn on.
*Tip: The LED will light on for 20 seconds. The
next step must be entered while LED is on.
STEP3 Point the remote control toward the
equipment and alternately press
the [CH+] (or [CH-]) button and the
[MUTE] button. If the right code
number is sent, the equipment will
turn off.
*Tip : You can verify that you selected the
correct code by pressing the [MUTE]
button again. The equipment should
either turn on or turn off.
STEP4 Press the same [DEVICE] button STEP4 Store the three-digit code
to store the code. The LED will number by pressing the [VCR
blink twice to confirm that the POWER] button once again.
code has been stored. The LED will blink twice to
confirm that the code has been
stored.
C. To Find the Three Digit Code
Number That was Stored in the
E. Volume Punch Through:
Device.
By following the steps below, the user can
STEP1 Press the [DEVICE] button (TV
program the volume controls (Volume UP,
POWER or VCR POWER) you wish
Volume Down and MUTE) from one device
to verify and the [SEL] button
to operate in another device mode.
simultaneously for 3 seconds.
The default volume control settings on the
*Tip : The LED will turn on for 20 seconds.
remote control is TV volume control. If you
The next step must be entered while
wish to store the CABLE volume control in
the LED is on.
CBL mode, use the following steps.
STEP2 Press the [INFO] button.
STEP1 Press the [CABLE POWER]
button and the [SEL] button
The LED will blink number of times
indicating the number of each digit of the simultaneously for 3 seconds.
code number. Each digit is separated by a 1
*Tip : The LED will light on for 20
second interval of the LED being turned off.
seconds. The next step must be
Example : One blink, three blinks and entered while the LED is on.
eight blinks with an interval of 1
STEP2 Press the [VOL +] button.
second of LED being turned off,
indicates the code number 138. STEP3 Press the [CABLE POWER]
button. The LED will blink twice
Note : Ten blinks is equal to the number 0.
to confirm the programming.
To return to original state:
D. Programming a second TV to
If you wish to restore the TV volume
VCR Mode.
control in CBL mode, repeat the above
steps by pressing [TV POWER] in step 3.
STEP1 Press the [VCR POWER] button to
be programmed and the [SEL]
button simultaneously for 3
F. LOW BATTERY WARNING:
seconds.
When the battery is low (2.0V-2.3V) and
needs to be replaced with fresh
*Tip : The LED will turn on for 20
seconds. The next step must be batteries, the LED will blink twice
entered while the LED is on. whenever a device [POWER] button is
pressed to turn on equipment.
STEP2 Press the [TV POWER] button
to pick up the TV code table.
G. Memory Lock System:
STEP3 Point the remote control
This remote control is designed to retain
toward the equipment and
programmed memory for 10 years even
enter the three-digit code
after batteries are removed from the
number assigned to your TV
remote control
brand from the code tables.