NAPCO PIR1680P Installation Instructions

PIR1680P/PT PET IMMUNE PIR • INSTALLATION INSTRUCTIONS
SPECIFICATIONS
Operating Voltage: 10.6 to 16Vdc nominal Filtered DC with battery
backup from control panel. (see Note 1)
Standby Current: 28mA at 12VDC (nom.) 33mA at 16VDC (nom .)
Alarm Current: 28mA at 12VDC (nom.) 33mA at 16VDC (nom.)
Alarm Output:
Normally-Closed Form-A Relay
Contact Rating:
1 OOmA, 24VDC w/ internal1 on limiting resistor
Trouble Output:
J
Active Low Open Collector with 47n current limiting
-
- -
resistor ~100mA . Max.)
· - -
Trouble Output Time: Latched (until restore) for High or Low temp.
Momentary (3 sec.) for Self Diagnostics failure
Operating Temperature: -1o· to +so· c (14·F to 122·Fl
Temperature Compensation Yes
Low Temp Output Setting:
40•F +/- 4•F (fixed)
-
-·
High Temp Output Setting: go•F +I- 4 · F (fixed)
Coverage I Pet Immunity: 45' x 45' High Sense Mode (30 lb Pet Immunity)
40' x 40' Normal Sense Mode (65 lb Pet Immunity)
Mounting Height: 6.5ft- 1Oft. (7.5ft. Recommended)
Coverage Angle : 85° at Maximum Range.
Dimensions: 3.3in x 2.5in x 1.9in (8.4cm x 6.4cm x 4.8cm) (HxWxD)
Shipping Weight: 5oz (142g)
Note 1: Th1s umt 1s Intended for operation from a power source that provides a 4
hour battery backup in the event of a power failure .
NOTE:
Pet Immunity has not been evaluated by
UL.
LOCATING THE DETECTOR
Select a location that will provide the required coverage and allow the detector to
be mounted at a height of 6.5ft. to 10ft. Comer mounting is preferred as it provides
the best overall coverage. Choose a location where the path of an intruder will
most likely cross beams, as opposed to walking towards or away from them.
• Avoid mounting the detector in close proximity to sources of heat, space heaters
and air ducts which may blow hot air directly onto the detector.
• Do not mount the unit where the sun can shine directly on it.
• Do not aim the detector
at
a stai[case wh ich a pet has access to.
• Do not mount the detector near furniture or objects higher than 4 feet tall which
a pet may climb onto (such as a couch within 6 feet of the detector)
NOTE: For 65 pound pet immunity: remove look-down lens and remove SEN
8
(a) TOP VIEW
MOUNTING
Standard (Nonnal Sense) Coverage Pattern.
For High Sense, increase range from 40' to 45'
jumper.
7.5'~
a
LO O KOO WN
ZONE
40'
(b) SIDE VIEW
1. Use a screw driver to carefully lift the lens cover from the housing.
2. Remove the circuit board from the housing by removing the screw in the center
of the board .
3. Determine the wire entry points on the housing. The housing provides four
possible wire entry points,
two
for surface wiring and
two
for hidden wiring .
Determine which entry is most convenient and punch out or remove the thin
plastic section.
4. Mount the housing to the wall. There are three mounting options to choose from:
flat wall mounting, corner mounting or swivel bracket (SVL2) mounting on ceiling
or wall. If using the swivel bracket refer to the instructions with the bracket. For
wall or corner mounting simply hold the case in the desired location and using
the supplied screws push through the appropriate thin wall mounting screw
holes and attach the unit with two or four screws. Note: Do not over tighten the
screws as th is can distort the case and compromise the air seal of the unit,
because not all walls are flat and all comers are square. Reinstall the circuit
board and proceed to wire the detector.
I
WIRING & TERMINAL DESCRIPTIONS
Refer to the wiring diagram and connect the appropriate wire to the corresponding
terminal. When the wiring is completed , seal the opening around the wire entry
hole and any other unused holes with the supplied sealer.
r ----- ----------,
DETAIL '
7 6
'[@]
Tamper Optional: :
PT
version only :
TAMPER :
: N.C. (WHEN SET) :
TAMPER SWrTCH
-~!1io\l) ) ~
Opti onal :
PT
version only
LOOK DOWNLENS
~r----"·
(REMOVE FOR 651b.
I
PET IMMUNITY) .. LT
CICIIZI
HT LT
INSTALLHTTO ENABLE
~J
TROUBLE OUTPUT
0~
HIGH TEMP
INST Alll T TO ENABLE TROUBLE
OUTPUT ON LOW TEMP
5 4
SEN ST
3 2
12V
TEMPERATURE SENSOR
MOUNTING HEIGHT SCALE
(AL IGN WITH INDEX IN CASE)
INSTAll ST TO ENABLE
TROUBLE OUTPUT ON
ICI::II
~ SELF-TEST
FAILURE
L_
OFF FOR NORMAL SENSITIVITY
(6 5 1 b. PET IMMUNITY)
ON FOR HIGH SENSITIVITY
(30 lb.
PET IMMUNITY)
PIR1680P'T-Eiircuit Board-Detail
LOW AND HIGH TEMP ALERT MONITORING
Low Temperature Alert for Heating System Monitoring (Patented).
To enable the Low Temperature Output in the case of the ambient temperature
falling below 40•F, place a jumper across pins L T and wire the Trouble Output
(terminal 5) to the positive terminal of a zone programmed for 24 Hour protection .
This output will remain active as long as the temperature remains below 40•F,
when the temperature rises several degrees above 40• this the output will reset.
High Temperature Alert for Cooling System Monitoring (Patented)
To enable the High Temperature Output in the case of the ambient temperature
rising above go•F, place a jumper across pins HT and wire the Trouble Output
(terminalS) into the positive terminal of a zone programmed for 24 Hour protection.
This output will remain active as long as the temperature remains above go•F,
when the temperature falls several degrees below go• the output will reset.
Both High Temp. and Low Temp. Alert may be enabled simultaneously.
Place a jumper across pins L T and place a jumper across pins HT.
Local Indication
If the unit is in a high or low temperature condition , the LED will glow dimly instead
of being completely off during periods of inactivity.
Testing
The temperature monitoring feature may be tested for low temperature alert using
freeze spray and for high temperature alert using a hairdryer. Refer to the Circuit
Board Detail for the location of the temperature sensor and apply the cold I heat
accordingly. The temperature sensor will respond to an active temp alarm condi-
tion once every ten minutes, or upon each sensing of motion. Either wait for the
sensor to detect the temp alarm, or cause a motion alarm to speed up the test.
Observe the LED for a dim glow and check the control panel for the proper re-
sponse.
z
Napco Security Systems, Inc.
NAP CO®
333 Bayview Avenue, Amityville, New York 11701
For Sales and Repairs, (800) 645-9445
For Technical Service, (800) 645-9440
Wl1136 8/2002