Quoizel TF3341T Assembly Instruction Sheet

6 CORPORATE PARKWAY
, .
GOOSE CREEK SC 29445
. .
www quoizel com
Please go to www.quoizel.com
Tools Required: None.
Light Source: (2) A19 Medium Base Bulbs 75W Maximum
Estimated Assembly Time: 20-30 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
A. Insert the Glass Panel into the Frame and secure the
Glass Panel with Tabs at the edges of the Frame.
B. Thread the Socket Assembly onto the Base and make sure
sockets are parallel with Base. Hand tighten until snug.
C. Thread the hex nut end of the Nipple with Hex Nut into the
hex coupling on the top center of the Socket Assembly. By
using the pliers, thread the hex nut against the hex
coupling and hand tighten until snug.
D. Place the Spacer Tube and the Check Ring over the top
end of the Nipple and secure with the Small Knurled Nut.
Hand tighten until snug.
E. Thread the Big Knurled Nut onto the top end of the Nipple
and adjust it to proper location for rest components. Place
the Flat Washer, the Shade, the Big Cap, the Small Cap
and the Rubber Washer over the top end of the Nipple.
Make Shade is parallel with Base. Secure with the Finial
and hand tighten until snug.
F. Insert bulbs onto sockets and screw snugly into place.
Your fixture is now assembled and ready to use. Enjoy!
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
2017 QuoizelInc.
Assembly Instruction Sheet #IS-TF3341T
for product cleaning tips. Go to the
Incorrect
base/ socket/
shade Orientation shade Orientation
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
For Style TF3341T
Care + Maintenance selection.
Tab
Tab
Correct
base/ socket/
1of2
Frame
Small Cap
x 1
x 1
Glass Panel
x 4
Flat Washer
x 1
Small
Knurled Nut
x 1
3.5"L
Spacer Tube
x 1
Socket
Assembly
x 1
Cord
ReleasedDate:2017-10-11
Finial
x 1
Rubber Washer
x 1
Big Cap
x 1
Shade
x 1
Big Knurled
Nut x 1
Check Ring
x 1
4"L Nipple
with Hex Nut
x 1
Bulb (not
included)
Base
x 1