Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Pearl PA2515DG
Summary of Contents for Pearl PA2515DG
- Page 1 5" PNEUMATIC DISC GRINDER MODEL PA2515DG OWNER’S/OPERATOR’S MANUAL serial number - You should record the Serial Number of your polisher on this Owner’s/Operator’s Manual Caution! Read Safety and General Instructions carefully before using the tool for the first time. REV. 1...
-
Page 2: Table Of Contents
ABOUT AIR PRESSURE AND VOLUME ......12 ix. ABOUT SILENCE ..............13 x. MAINTENANCE ..............13 xi. REPLACEMENT PARTS LIST ..........14-15 xii. HOW TO ORDER PARTS ............15 xiii. CUSTOMER SERVICE ..........Back cover PEARL LIMITED WARRANTY ......Back cover PEARL CONTACT INFO ........Back cover - 2 -... -
Page 3: General Safety Rules And Precautions
ii. GENERAL SAFETY RULES AND PRECAUTIONS WARNING! Read all instructions. As with all machinery there are certain hazards involved with operation and use of the machine. The following basic safety precautions should be followed at all times to reduce the risk of fire, electric shock and serious personal injury to you or others. - Page 4 (plugs or muffs) during that is damaged should be extended periods of carefully checked to ensure operation. that it will operate properly and perform it’s intended 11. Do not overreach. Keep function. Check for proper footing and balance alignment of moving parts, at all times.
- Page 5 purpose other than designated 29. Do not direct the tool towards by the manual. bystanders and/or animals. Fragments of workpiece or of a 22. Follow ANSI Z87.1 or broken accessory may fly away local/national standards for eye- and cause injury. Keep wear and other personal bystanders out of work area.
- Page 6 48. Never place hand or face near a contains oil and contaminated moving accessory. moisture. Make sure it is not 49. Use only genuine Pearl directed towards you or anyone replacement parts for repairs. within the work area. 50. Always turn it off and disconnect 40.
- Page 7 SPECIFIC WARNINGS increase the number of FOR PA2515DG revolutions or strokes causing potential failure and accidental 1. Use the Pearl PA2515DG for dry injury. grinding only. 3. Use only identical replacement 2. Only use a Backing pad rated for parts when servicing.
- Page 8 Lubricating the tool before and 13. Do not leave accessories attached during work is not needed. to the threads of the spindle. This Excessive oil will turn into a tar- can result in damage to the like substance inside the tool, spindle or accessory.
- Page 9 WARNING! CALIFORNIA PROPOSITION 65: Sawing and drilling generates dust. Excessive airborne particles may cause irritation to eyes, skin and respiratory tract. To avoid breathing impairment always employ dust controls and protection suitable to the material being saw or drilled in accordance with OSHA (29 CFR Part 1910.1). Diamond blades improperly used are dangerous.
-
Page 10: Silica Dust Warning
iii. SILICA DUST WARNING Grinding/cutting/drilling of tile, masonry, concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis. -
Page 11: Operation Procedures
vi. OPERATION PROCEDURES 1. Connect the coupler to the (1) air inlet 4. When the grinding stone is installed, on the rear side of tool. press the spindle lock button (3) at the angle head, and the spindle will stop. Turn it counterclockwise with the pin spanner, and firmly tighten the spindle. -
Page 12: Specific Caution For Air Supply
vii. SPECIFIC CAUTION FOR AIR SUPPLY 1. Use a clean lubricated air supply that will 4. Use safety shuttle valves so air flow can give a measured pressure at the tool of be stopped in case of a line break. 90 PSI/6 bar (0.6 MPa) 5. -
Page 13: About Silence
ix. ABOUT SILENCE To comply with OSHA code 1926.52 Noise exposure Standard, this grinder comes fitted with and internal silencer. When operated within factory specifications (80-90 PSI @ 16 CFM) the silencer bring the noise to less than 84 db. The silencer also provides back pressure to help assure that you are getting a constant RPM level. -
Page 14: Replacement Parts List
xi. REPLACEMENT PARTS LIST PART NAME QTY. PT NUMBER PART NAME QTY. PT NUMBER Retainer 889887 16 Pendulum 670294 Screen 889888 17 Governor 670295 Inlet Bushing 889889 18 Governor Spring 670296 Deflector 889890 19 Adjust Screw 670297 O-Ring 889891 20 Adjust Nut 670298 Valve Spring 670283... -
Page 15: How To Order Parts
(1) They must be current products; (2) Items All illustrations displayed in this manual are returned for replacement or refund should be the property of Pearl Abrasive Co. and shall in original cartons and must be accompanied not be duplicated or reproduced without the by a packing slip with the following express written consent of Pearl Abrasive Co. -
Page 16: Customer Service
If requested, we may arrange for our sales representatives to hold a training class for product knowledge at dealer’s location. CORPORATE OFFICE: GEORGIA • USA 455 SATELLITE BOULEVARD, SUWANEE, GA 30024 PH 800-969-5561 ONTARIO • CANADA 375-2 PIDO ROAD, PETERBOROUGH, ONTARIO K9J-6X7 PH 800-387-0008 www.pearlabrasive.com ©2024 PEARL ABRASIVE CO. • 03/24...
Need help?
Do you have a question about the PA2515DG and is the answer not in the manual?
Questions and answers