Advertisement
BLACK LABEL SERIES AMPLIFIERS
OWNER'S MANUAL &
INSTALLATION GUIDE
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 5
ZONE 6
ELURA AMP100/6.2
100
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 5
ZONE 6
6 CHANNEL, 3 ZONE AMPLIFIER
AND
ELURA AMP80/12
12 CHANNEL, 6 ZONE AMPLIFIER
AND
ELURA AMP80/16
16 CHANNEL, 8 ZONE AMPLIFIER
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 5
ZONE 6
ZONE 7
ZONE 8
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Elura BLACK LABEL Series
Summary of Contents for Elura BLACK LABEL Series
- Page 1 BLACK LABEL SERIES AMPLIFIERS OWNER’S MANUAL & INSTALLATION GUIDE ZONE 1 ZONE 2 ZONE 3 ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 ZONE 4 ZONE 5 ZONE 6...
- Page 2 FCC Statement...
- Page 3 This amplifier is also equipped Each pair of channels or zones has a with a pair of BUS line outputs for Thank you for purchasing Elura amplifier red and blue LED to indicate its sending signal to additional amplifiers if products.
- Page 4 respective channel to make the loops in audio cables. If a ground loop NOTE: the amplifier has a delay of selection. Pick the desired input source occurs, adjust the switch to reduce or approximately 15 minutes before it goes and position the switch to BUS 1 (for the eliminate any audible hum or buzz noise into standby when using the “Auto”...
-
Page 5: Setup And Installation
LED Indicators and Anti-Clipping Circuitry: What You Need to Know Front Panel LED Reference Chart Note: If a channel LED is RED, there is a fault and an issue needs to be fixed. Once settled, the indicator should turn back to BLUE if the zone is being used or OFF if the zone is not being used. - Page 6 Typical Multi-Zone Input AC & Power Cord Caution The AMP100/6.2，AMP80/12 and The fuse holder is located directly under Wiring Example AMP80/16 can operate in 110V and 220V the power socket. It contains one extra environments. Before powering the 10 ampere, 250V fuse. amplifier on, make sure that the Input Ensure that the STEREO/BRIDGE AC Selector is in the correct position...
-
Page 7: Wiring Configurations
Wiring Configurations Fig. 5 Standard 2-Channel Stereo Wiring 1.Attach the source to the RCA LINE IN or BUS INPUT 2.Set the input switch to the appropriate source 3.Set the ST/BR switch to ST (stereo) 4.Attach two speakers to the phoenix connector, left &... - Page 8 Wiring Configurations (continued) Dual Passive Subwoofer Wiring - Bridged Output Fig. 8 1.Attach the source to the LINE IN or BUS IN 2.Set the input switch to the desired source 3.Connect a single RCA wire from the SUB OUT of one zone to the next zone’s LINE IN LEFT channels 4.Connect the speakers to the phoenix connector of the first zone and set it to ST for...
-
Page 9: Specifications
Connecting Multiple Amplifiers If connecting multiple amplifiers, run an Fig. 10 RCA cable from one of the BUS OUTPUTS of amplifier 1 to a BUS INPUT of amplifier 2. This will supply the source signal to the additional amplifier. Ensure that the input selector switches on amplifer 2 are in the correct BUS INPUT position. -
Page 10: Troubleshooting
Note that the unit is in standby mode when the power LED is red, and the zone status LEDs are not Elura amplifiers are designed to function No audio from one or more channels trouble-free. Most problems that occur •... -
Page 11: Product Warranty
• Audio cable to the source component installed, modified, disassembled and/or repaired by anyone other than Elura or is not connected properly or the cable is defective. Check connections or our appointed repair facility.
Need help?
Do you have a question about the BLACK LABEL Series and is the answer not in the manual?
Questions and answers