Hama Roundly Manual

Explanation of Warning Symbols and Notes Warning

This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.
Note
This symbol is used to indicate additional information or important notes.

Package Contents

• „Roundly" radio-controlled alarm clock
• 1 AA battery
• These operating instructions

Getting Started

Inserting the battery

Remove the battery that was already inserted into the clock, remove the protective film if necessary as well as the contact interrupter and the re-insert the battery with the correct polarity. The clock is ready for operation.

Replacing the battery

• Open the battery compartment on the back of the product.
• Remove and dispose of any used batteries. Insert the new battery (AA). Ensure that the polarity of the battery corresponds to the symbols in the battery compartment.
• Close the battery compartment.

Operation

Automatic time setting using the DCF signal

• Once you have removed the contact breaker, anacoustic signal sounds and the alarm clock automatically starts searching for a DCF signal.
• After approx. 5-10 minutes (depending on howquickly the radio signal was received), the hands will set themselves to the correct time.

Setting the time manually

• If the correct time has not been set after approx. 10minutes, this means the clock could not find a DCF signal.
• Press and hold theM.SET button to manually set the correct time. Release the M.SET button once you have reached the required time.
• The clock automatically continues to search for the DCFsignal on a daily basis. If the signal is received successfully, the manually set time is overwritten.
• You may need to change the installation location andavoid areas with possible sources of interference (cordless and mobile telephones, wireless speakers, etc.).

Starting manual reception

• Once the clock is running, press theREC button for 3 seconds. This will set the hands to the 12:00 position. Now the clock starts searching for the DCF signal.
• If no signal has been received, the clock will show thetime previously saved.

Alarm

Setting the alarm

• Move the setting wheel on the back of the alarm clockto set the required alarm time.
• To activate/deactivate the alarm, move the slide switchto theON or OFF position.

Stopping the alarm/snooze function

• If the alarm is activated, it is triggered at the set timeand an alarm signal sounds for two minutes with increasing volume. The alarm automatically stops after this time and is then triggered again at the set alarm time.
• To stop the alarm early, move the slide switch to theOFF position.
• Move the slide switch back to theON position to activate the alarm for the set alarm time.

Note – Snooze function

• While the alarm signal is sounding, press theSNOOZE/LIGHT button to activate the snooze function. The alarm signal will be stopped for 5 minutes, after which it will sound again.
• The snooze function can be activated nine consecutive times.

Backlight

• If you press the SNOOZE/LIGHT button, the clock face will light up for approx. 5 seconds.

RESET function

• If, for whatever reason, the clock has not been setcorrectly, you can reset it.
• Use a metal object (such as a needle) to short-circuitthe clock by means of the ‚RESET' button on the rear side. All hands will move to the 12:00 position.
• After approx. 5-10 minutes (depending on howquickly the signal was received), the hands will automatically set themselves to the correct time.

Care and Maintenance

Only clean this product with a slightly moist, lint-free cloth, and do not use aggressive cleaning agents. Make sure that water does not get into the product.

Technical Data

	Elegance Pro radio-controlled alarm clock
Power supply	1.5 V, 1 AA battery

Safety Instructions

• The product is intended for private, non-commercialuse only.
• Protect the product from dirt, moisture and overheat-ing, and only use it in a dry environment.
• Do not use the product in areas where the use of electronic devices is not permitted.
• Do not place the product near interference fields, metal frames, computers, TVs, etc. Electronic devices and window frames can negatively affect the product's functionality.
• Do not drop the product and do not expose it to anymajor shocks.
• Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.
• Do not modify the product in any way. Doing so voids the warranty.
• Keep the packaging material out of the reach ofchildren due to the risk of suffocation.
• Dispose of packaging material immediately accordingto locally applicable regulations.

Batteries

• When inserting batteries, note the correct polarity (+ and - markings) and insert the batteries accordingly. Failure to do so could result in the batteries leaking or exploding.
• Only use batteries (or rechargeable batteries) that match the specified type.
• Before you insert the batteries, clean the battery contacts and the polar contacts.
• Do not allow children to change batteries without supervision.
• Do not mix old and new batteries or batteries of a different type or make.
• Remove the batteries from products that are not being used for an extended period (unless these are being kept ready for an emergency).
• Do not short-circuit batteries.
• Do not charge batteries.
• Do not throw batteries in a fire.
• Keep batteries out of the reach of children.
• Never open, damage or swallow batteries or allow them to enter the environment. They can contain toxic, environmentally harmful heavy metals.
• Immediately remove and dispose of dead batteries from the product.
• Avoid storing, charging or using batteries in extreme temperatures.