Philips EasySense SNS212 MC Quick Installation Manual

Note: Below data applicable for SNS212 MC..
Electrical Information
Input Voltage Powered by SR driver low-voltage interface
Current Consumption 13mA
Nominal Power Consumption 200mW
< 1 W on luminaire level, including driver standby power
Standby Power
Occupancy Sensing
Passive infrared (PIR)
Type
Default enabled and active for SNS211 MC. Activated upon commissioning for SNS210 MC.
Occupancy Based Control
Default Auto on/off. Other options are: Manual on/off, Manual on/auto off
Occupancy Mode
1 - 100%
Eco On Level
Hold Time 5 - 100 minutes
Viewing Angle X = 62°, Y = 84° ( See detection pattern)
Background Light Level 1 - 100%
7 - 100 minutes + infinite
Prolong Time
1 - 25 sec
Grace Fading
Response Time/Fading to Switch On/Off 1 sec
Daylight Sensing
Enable/Disable Default enabled
40° (half value sensitivity); 2% cut-off point at 75°
Viewing Angle
Task Tuning
Field Task Level 1%-100%
Environment & Approbation
Operating Ambient Temperature Range 0°C to 55°C
20% – 85% non condensing
Operating Humidity
Storage Temperature -25 °C - 85 °C
Storage Humidity 0-95% non condensing
Max Case Temperature (Tcase) 55°C
Agency Approbations UL, FCC; Tested and approved for use in plenums
Limited Warranty 5 years
Xitanium SR
Digital Interface
Other
Status Indicators After commissioning: Red LED on: Motion is detected;
Yellow LED on: Vacancy detected & Sensor is functional
Four (max)
No. Drivers per Sensor
Field Configuration via BLE, parameters set via Philips MasterConnect App
Operation and Configuration via Mobile App
SNS212 MC requires commissioning to operate. The node can be commissioned and configured via the Philips MasterConnect app through
Bluetooth LE. For a complete description of the features and default settings—as well as details on the app—refer to
www.philips.com/easysense.
FCC and IC Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules for the United
States and Industry Canada (IC) license-exempt RSS standard(s). These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment and is intended for commercial use only. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Any
changes or modifications not expressly approved by Signify could void the user's authority to operate this equipment.
This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
Déclaration De Conformité À La Fcc/Ic
Cet équipement a été testé et jugé conforme aux limites d'un appareil numérique de classe A, conformément à la partie 15 des règles de la FCC pour
les États-Unis et à la/les norme(s) liée(s) à RSS exempt(e)s de licence d'Industrie Canada (IC). Ces limites sont conçues pour fournir une protection
raisonnable contre les interférences nuisibles lorsque l'équipement est utilisé dans un environnement commercial et est destiné à un usage
commercial uniquement. Cet équipement génère, utilise et peut émettre de l'énergie radiofréquence et, s'il n'est pas installé et utilisé conformément
au manuel d'instructions, peut causer des interférences nuisibles aux communications radio. L'exploitation est soumise aux deux conditions
suivantes : (1) Cet appareil ne doit pas causer d'interférences nuisibles, et (2) cet appareil doit accepter toute interférence reçue, y compris les
interférences pouvant provoquer un fonctionnement indésirable. L'exploitation de cet équipement dans une zone résidentielle est susceptible de
provoquer des interférences nuisibles, auquel cas l'utilisateur sera tenu de corriger les interférences à ses frais. Tout changement ou modification
non expressément approuvé par Signify pourrait annuler l'autorisation de l'utilisateur d'utiliser cet équipement.
Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps.
© 2023 Signify Holding. All rights reserved. The information
provided herein is subject to change, without notice. Signify
does not give any representation or warranty as to the accuracy
or completeness of the information included herein and shall
not be liable for any action in reliance thereon. The information
presented in this document is not intended as any commercial
offer and does not form part of any quotation or contract,
unless otherwise agreed by Signify. Philips and the Philips
Shield Emblem are registered trademarks of Koninklijke Philips
N.V. All other trademarks are owned by Signify Holding or their
respective owners.
SNS212 MC QIG 03/23
Signify North America Corporation
400 Crossing Blvd, Suite 600
Bridgewater, NJ 08807
Tel. 855-486-2216
Signify Canada Ltd.
281 Hillmount Rd,
Markham, ON, Canada L6C 2S3
Tel. 800-668-9008
Sensors
EasySense
Fixture-Mount
Philips EasySense Quick Installation Guide
Wireless Node Part Number
Commercial Product Name
EasySense Fixture-Mount Sensor
LED Drivers
The EasySense SNS212 MC sensors are compatible with Xitanium SR drivers. To find the SR
driver that fits your application needs and for product specifications, please visit
www.Signify.com/xitaniumsr
Wiring Diagram*
DA+
DA–
XITANIUM SR
LED+
LED+
NC
LED DRIVER
GROUND
LED-
NEUTRAL
LED-
LINE
Connection Color Connection Color
Green Ground Purple DA+
White Neutral Brown DA-
Red LED+
Black Line
Blue LED-
* Wiring diagram for 40W driver shown. Other drivers have different wiring diagrams.
Consult datasheet for driver for applicable wiring diagram.
Order Code
SNS212 MC,12NC:929003416313
Connectors
EASYSENSE
DA
DA
Connectors
Use 18AWG solid copper
(non-polarized)
wire, rated >=600V/90C.
Strip wire to 3/8".