Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Sensor Therm SIRIUS SS09
Summary of Contents for Sensor Therm SIRIUS SS09
- Page 1 Pyrometers SIRIUS SS09 / SI16 Operating Manual...
-
Page 2: Table Of Contents
Pyrometers SIRIUS SS09 / SI16 Content Content General ............................... 4 Information to this Manual ......................4 CE Conformity and Standards ....................4 Limitation of Liability ........................4 Terms of Warranty ........................4 Copyright ........................... 4 Explanation of Symbols ......................5 Disposal ............................ - Page 3 Pyrometers SIRIUS SS09 / SI16 Content SensorTools Software ........................15 Installation ..........................15 Program Start .......................... 15 6.2.1 Connecting the Pyrometer ....................15 Software Window ........................16 Main Window → Graphs ....................16 6.3.1 Control Window ........................18 6.3.2 Device Settings and Configuration ..................18 Data Playback .........................
-
Page 4: General
Pyrometers SIRIUS SS09 / SI16 General General Information to this Manual This manual enables the safe and efficient use with the device. The manual is part of the instrument and has to be kept in a location where users always have access to. -
Page 5: Explanation Of Symbols
Pyrometers SIRIUS SS09 / SI16 General Explanation of Symbols Signal words in combination with symbols indicate safety and information in this manual. Please note these instructions for safety reasons. CAUTION: This combination of symbol and signal word indicates a potentially dangerous situation that can result in minor or moderate injury if not avoided. -
Page 6: Safety
Pyrometers SIRIUS SS09 / SI16 Safety Safety General Any person who is tasked to carry out work with the device must have read and understood the operat- ing instructions before beginning. Operation and maintenance of the system may only be performed by trained personnel. -
Page 7: Electrical Connection
Pyrometers SIRIUS SS09 / SI16 Electrical Connection Electrical Connection Cable Colors and Pin Assignment (14-wire connection cables) The electrical connection of the pyrometer (supply voltage and measuring signal) will be done via the connector on the Mains filter and voltage stabilization box. For this purpose, pre-assembled connection cables are available as accessories (see Accessories). -
Page 8: Digital Inputs
Pyrometers SIRIUS SS09 / SI16 Electrical Connection 3.1.4 Digital Inputs By applying the supply voltage to the cable gray (pin H) or +24 V pink (Pin J) it can be +24 V White ▪ externally reset the peak picker ▪ externally switch on the targeting light... -
Page 9: Interface Converter (Accessory)
Pyrometers SIRIUS SS09 / SI16 Mechanical Installation When operating multiple devices (up to 32 are possible), each device needs to assign its own address (directly on the device or via software SensorTools), under which it can be addressed later. For this purpose, initially, each device must be connected individually and provided with an address (00-97). -
Page 10: Ambient Temperature
Pyrometers SIRIUS SS09 / SI16 Mechanical Installation Ambient Temperature Sirius pyrometers are designed for ambient temperatures between 0 and 70°C. Operation outside this temperature leads to incorrect measurements and may damage the unit. To comply with the permitted ambient temperature sufficient dis- tance from the (hot) measuring object is observed. -
Page 11: Setting The Measuring / Focus Distance
Pyrometers SIRIUS SS09 / SI16 Mechanical Installation Turn on / off: Via the targeting light button on rear panel or the button if using a connection cable with laser targeting button or via software Sen- sorTools (see Control Window (Settings). -
Page 12: Calculation Of The Spot Size Diameter Outside The Focused Distance
Pyrometers SIRIUS SS09 / SI16 Configuring the Pyrometer / Parameters 1.85 13.3 OP09-B0 12.9 2.25 12.1 11.2 15.7 14.6 13.3 OP09-C0 1000 12.5 14 mm 1250 11.9 1500 11.5 1750 11.2 2000 14.5 ▪ The optics lens can be replaced after loosening the screw ring. They are interchangeable without re- calibration. -
Page 13: Temperature Simulation
Pyrometers SIRIUS SS09 / SI16 Configuring the Pyrometer / Parameters Temperature Simulation About SensorTools software, a test current can be set to the output in order to simulate a temperature (see 6). 5.2.1 Emissivity ε The emissivity indicates the radiation... -
Page 14: Response Time T 90
Pyrometers SIRIUS SS09 / SI16 Configuring the Pyrometer / Parameters Measurement deviations at a 10% false set emissivity +10% -6.5°C -10.5°C at a temperature of 700°C: -10% +7°C +11.5°C Response Time t The response time specifies the time that the pyrometer requires to track 90% of a sudden temperature change on the signal output. -
Page 15: Sensortools Software
Pyrometers SIRIUS SS09 / SI16 SensorTools Software SensorTools Software Installation With the minimum requirements devices can be connect and configured. When capturing or recording data, the performance is potentially impaired, that is errors or interruptions in data transfer can occur. -
Page 16: Software Window
Pyrometers SIRIUS SS09 / SI16 SensorTools Software Software Window The most measuring tasks can be done with the software default settings, but customized settings uti- lize the full capabilities of pyrometer and software. Control Window Main Window Measuring temperature Data recording, data recording... - Page 17 Pyrometers SIRIUS SS09 / SI16 SensorTools Software ▪ Select display graphs: - Depending on the device type, different graphs can be displayed or hidden; the color can be changed by right-clicking on a color field. ▪ Record: The transferred measured value data can be recorded on hard disk for subsequent analysis. Click the recording button to start and stop recording, the button flashes when recording is active ( Pause interrupts the recording.
-
Page 18: Control Window
Pyrometers SIRIUS SS09 / SI16 SensorTools Software Control Window ▪ T stands for temperature and indicates the measur- ing temperature. ▪ The internal device temperature (DT) depends on the ambient temperature and the device self-heating. Measuring value - Sirius models are permissible up to maximum Int. -
Page 19: Service Functions
Pyrometers SIRIUS SS09 / SI16 SensorTools Software ▪ Service functions To back up, for printing or restore de- vice parameters or create service files for remote diagnosis of problems. - Create configuration file: A configuration file includes all device settings made by user. This can be used e.g. to set- up a new pyrometer with the same values and settings or to save the current status in case of a device replacement. -
Page 20: Communication / Options
Pyrometers SIRIUS SS09 / SI16 SensorTools Software Communication / Options ▪ Sprache/ Language: Selects between German and English user interface. ▪ Print configuration file has the same function as in the device configuration under "service func- tions": Prints a stored device settings file. -
Page 21: Technical Data
Pyrometers SIRIUS SS09 / SI16 Technical Data Technical Data 50 – 400°C 100 – 600°C 150 – 900°C Temperature ranges Temp. sub ranges Any temperature sub-range adjustable within the temperature range (minimum span 50°C) Spectral range 2–2.6 µm Detector InGaAs... -
Page 22: Dimensions
Pyrometers SIRIUS SS09 / SI16 Technical Data Dimensions Storage Store packages under the following conditions: ▪ Do not store outdoors ▪ Avoid mechanical vibrations ▪ Store dry and dust-free ▪ Storage temperature: -20 to 70°C ▪ Do not exposed to corrosive media ▪... -
Page 23: Accessories
Pyrometers SIRIUS SS09 / SI16 Maintenance Accessories It is recommended to purchase spare parts and accessories direct from Sensortherm (manufacturer). Ref. number Meaning AL10-XX * Connection cable with right angled connector and targeting light button AL11-XX * Connection cable with right angled connector... -
Page 24: Communication Via Serial Interface / Interface Commands
Pyrometers SIRIUS SS09 / SI16 Communication via Serial Interface / Interface Commands Communication via Serial Interface / Interface Commands Interface commands are used to communicate directly with a Sensortherm pyrometer. Commands can be used to write an own access control or can be entered in the terminal field of the software Sensor- Tools (see Communication / Service) or entered via a terminal software. - Page 25 Pyrometers SIRIUS SS09 / SI16 Communication via Serial Interface / Interface Commands 1 = Maximum value is deleted (same function as triggering an external button to delete the maximum value) Read temperature range (8-digit hexadecimal number) ▪ The first four digits specify the beginning of temperature range in °C ▪...
-
Page 26: Index
Pyrometers SIRIUS SS09 / SI16 Index Index Interface commands ..........24 Interface converter (accessory) ......9 Interface delay ............. 14 Accessories ............23 Address ..............14 Alignment onto the measuring object ....10 Main window → data recording ......16 Ambient temperature ........... - Page 27 Pyrometers SIRIUS SS09 / SI16...
- Page 28 Sensortherm GmbH Weißkirchener Straße 2-6 D-61449 Steinbach Tel: +49 (0) 6171 887098-0 Fax: +49 (0) 6171 887098-989 E-Mail: info@sensortherm.com Internet: www.sensortherm.com © Sensortherm GmbH SIRIUS SS09 / SI16 (June 05, 2025)
Need help?
Do you have a question about the SIRIUS SS09 and is the answer not in the manual?
Questions and answers