Advertisement

Quick Links

USER MANUAL
MANUAL DE USUARIO
IMPORTANT: Read this Owner's Manual Completely before attempting to use this equipment.
Save this manual and keep it handy for quick reference. Pay particular attention to the safety
instructions we have provided for your protection. Contact your distributor if you do not fully
understand this manual.
Every SWEISS machine comes with 3 years of limited warranty. However, it is
necessary to take the machine to a free technical checkup every year (the
cost of labor is free, the spare parts will require payment), at any of the
SWEISS AUTHORIZED service centers, at the end of which the warranty will
be extended to the next year. The technical checkup must get done between
11 to 13 months from the purchase, and then 11 to 13 months from the rst
checkup. Not taking the machine to the annual checkup will void the
warranty.
Accessories or consumable parts like ground clamp, electrode holder and
torches ARE NOT COVERED BY WARRANTY, unless there is a manufacturing
defect.
Never use GAS, only AIR provided by a compressor, with a maximum pressu-
re of 120 PSI.
SKYCUT 690/1000– USER MANUAL/MANUAL DE USUARIO
SKYCUT 690/1000

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SKYCUT 690 and is the answer not in the manual?

Questions and answers

Summary of Contents for Sweiss SKYCUT 690

  • Page 1 USER MANUAL MANUAL DE USUARIO Every SWEISS machine comes with 3 years of limited warranty. However, it is necessary to take the machine to a free technical checkup every year (the cost of labor is free, the spare parts will require payment), at any of the SWEISS AUTHORIZED service centers, at the end of which the warranty will be extended to the next year.
  • Page 2 Ponga especial atencion a las intrucciones de seguridad para la proteccion de su integridad sica. Contacte a su distribuidor local si tiene alguna duda acerca de la operación de cualquiera de los equipos SWEISS . SKYCUT 690/1000 – USER MANUAL/MANUAL DE USUARIO...
  • Page 3: Table Of Contents

    3.2 POWER INPUT CONNECTIONS 3.3 GAS CONNECTIONS 4 OPERATION 4.1 FRONT PANEL DIAGRAM 4.2 SYMBOLS 4.3 CUTTING PREPARATION 5 MAINTENANCE & TROUBLESHOOTING 5.1 BASIC TROUBLESHOOTING GUIDE 5.2 PILOT ARC PROBLEMS 5.3 ARC PROBLEMS NOTES SKYCUT 690/1000 – USER MANUAL/MANUAL DE USUARIO...
  • Page 4: Security

    • Always disconnect the electrical supply before installation and initial adjustment of the machine. • Make sure the machine is well installed and correctly place and ground the object or metal being welded. SKYCUT 690/1000 – USER MANUAL/MANUAL DE USUARIO...
  • Page 5 • Read and understand the manufacturer’s instructions for this equipment and the consumables to be used, including the material in the safety data sheet and follow your employer’s safety practices. SKYCUT 690/1000 – USER MANUAL/MANUAL DE USUARIO...
  • Page 6 •Connect the work cable as close as possible to the welding work area. Work cables connected to the building structure can increase the possibility of the welding current passing through cables and alternate circuits. SKYCUT 690/1000 – USER MANUAL/MANUAL DE USUARIO...
  • Page 7: Parameters

    INSTALLATION AND ADJUSTMENT 2. Parameters SKYCUT 690/1000 – USER MANUAL/MANUAL DE USUARIO...
  • Page 8: Installation & Adjustment

    • An appropriate ow for the correct operation of the equipment must be supplied, with a minimum of 6cfm, with the indicated pressure. SKYCUT 690/1000 – USER MANUAL/MANUAL DE USUARIO...
  • Page 9: Operation

    INSTALLATION AND ADJUSTMENT 4. Operation 4.1 Front panel diagram SKYCUT 690/1000 – USER MANUAL/MANUAL DE USUARIO...
  • Page 10: Symbols

    4. Press and hold button 1 for 10 seconds to check the air inlet pressure and adjust until the alarm disappears. 5. After verifying that the air is dry and free and within the pressure limits, go to point 6. 6. Start using the equipment. SKYCUT 690/1000 – USER MANUAL/MANUAL DE USUARIO...
  • Page 11: Maintenance & Troubleshooting

    The arc automatically turns on when there is material and stops when there is not Air test mode It only serves to test the air outlet Air trouble notice Check pressure and ow Torch problem Consumables problem SKYCUT 690/1000 – USER MANUAL/MANUAL DE USUARIO...
  • Page 12: Pilot Arc Problems

    Incorrect connection between torch and power supply check that torch cables are properly connected. Work clamp poorly connected to workpiece. Equipment component failure: take it to an authorized service center for inspection and repair. SKYCUT 690/1000 – USER MANUAL/MANUAL DE USUARIO...
  • Page 13: Arc Problems

    Overheated equipment. Let it cool for ve minutes. Very low gas pressure. Adjust it at 4BAR / 60PSI. Consumables in poor condition. Check and change them. Equipment component failure. Take it to an authorized service center for inspection and repair. SKYCUT 690/1000 – USER MANUAL/MANUAL DE USUARIO...
  • Page 14: Notes

    NOTES SKYCUT 690/1000 – USER MANUAL/MANUAL DE USUARIO...
  • Page 15 NOTES SKYCUT 690/1000 – USER MANUAL/MANUAL DE USUARIO...

This manual is also suitable for:

Skycut 1000Skycut 1000 mxSwc1000

Table of Contents