Related Manuals for Meridian M2026MBKRV
Summary of Contents for Meridian M2026MBKRV
- Page 1 ITEM NO: M2026MBKRV M2026NBRV M2026WHRV CEILING FAN CEILING FAN OWNER'S MANUAL READ AND SAVE THESE INSTRUCTIONS FAN RATING AC 120V. 60Hz UL LISTED MODEL: AG794DL...
-
Page 2: Tools And Materials Required
1. TOOLS AND MATERIALS REQUIRED Philips screw driver Blade screw driver 11 mm wrench Step ladder Wire cutters 2. PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: a. Set of blades assembly (5) b. -
Page 3: Safety Rules
3. SAFETY RULES 1. To reduce the risk of electric shock, insure 10. Do not use water or detergents when cleaning electricity has been turned off at the circuit the fan or fan blades. A dry dust cloth or lightly breaker or fuse box before beginning. -
Page 4: Mounting Options
4. MOUNTING OPTIONS If there isn't an existing UL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building Outlet box structure. Use appropriate fasteners and building materials. -
Page 5: Hanging The Fan
5. HANGING THE FAN REMEMBER to turn off the power. Follow the UL Listed steps below to hang your fan properly: electrical box Hanger bracket NOTE: This ceiling fan is supplied with two types of hanging assemblies; the standard ceiling installation using the downrod with ball and socket mounting and the "close-to-ceiling"... - Page 6 CLOSE-TO-CEILING INSTALLATION Step 1. Pass the 120-volt supply wires through the center hole in the ceiling hanger bracket Canopy as shown in Fig. 5. Step 2. Remove the decorative canopy cover Decorative canopy cover from the canopy. (Fig. 8) Figure 8 Step 3.
-
Page 7: Make The Electric Connections
6. MAKE THE ELECTRIC CONNECTIONS POWER LINES 120V GREEN GROUND Remember to disconnect the power. Follow the steps below to connect the fan to your WIRING household wiring. Use the wire connecting nuts supplied with your fan. Secure the connectors with electrical tape. -
Page 8: Finishing The Installation
7. FINISHING THE INSTALLATION STANDARD CEILING INSTALLATION Outlet box Slide canopy up to the ceiling as shown in Screws Figure 14. Make sure you place the wires safely Hanger into the outlet box. Secure the canopy to the bracket hanger bracket with the four screws with your fan. -
Page 9: Attaching The Fan Blades
8. ATTACHING THE FAN BLADES CAUTION: Remove 5 rubber packing mounts and discard before installation. Step 1. Attach the blade to the blade bracket using the screws and fiber washers as shown in Figure 16. Start screw into bracket. Repeat for the two remaining screws. -
Page 10: Installing The Light Kit
10. INSTALLING THE LIGHT NOTE: Before starting installation, disconnect the power by turning off the circuit breaker or removing the fuse at fuse box. Step 1. Remove the 3 screws from the mounting plate. Mounting plate Step 2. While holding the light kit under your Connection plugs fan, snap together the wire connection plugs. -
Page 11: Operating Your Fan
12. FAN WITHOUT LIGHT (OPTIONAL) Step 1. Disassemble the switch housing from the light kit by removing nut and washer on the center of switch housing, you can keep the light kit for future use. Step 2. Attach the plastic plug to the switch housing. -
Page 12: Troubleshooting
14. TROUBLESHOOTING Problem Solution Fan will not start. 1. Check circuit fuses or breakers. 2. Check line wire connections to the fan and switch wire connections in the switch housing. CAUTION: Make sure main power is off. Fan sounds noisy. 1.
Need help?
Do you have a question about the M2026MBKRV and is the answer not in the manual?
Questions and answers