Subscribe to Our Youtube Channel
Related Manuals for Kohler K-99572-TLC
Summary of Contents for Kohler K-99572-TLC
- Page 1 Installation and Care Guide Lighted Mirror Français, page “Français-1” Español, página “Español-1” 1337912-2-A...
-
Page 2: Important Safety Instructions
LED lighting with a minimum rating of 150 W is recommended. *Outside North America, this device may be known as a Residual Current Device (RCD). SAVE THESE INSTRUCTIONS Specifications Electrical Service Light 120 V, 60 Hz, 0.4 A 1337912-2-A Kohler Co. -
Page 3: Tools And Materials
This installation is easiest when performed by two people. For K-99572-TLC and K-99573-TLC: When determining the height of the product, verify that the swinging panels will clear all obstacles (such as a faucet or light fixture). A minimum distance of 3″... - Page 4 Swinging Panels 3" (76 mm) Roughing-In For K-99572-TLC and K-99573-TLC: When determining the location of the mirror, verify that the swinging panels will clear all obstacles (such as a faucet or light fixture). Provide a minimum distance of 3″ (76 mm).
- Page 5 Make a mark on the centerline 2-1/2″ (64 mm) down from the top of the mirror. Align the power bar top with the line for the top of the mirror. Verify level, and mark the two hole locations at the top corners of the power bar. Kohler Co. 1337912-2-A...
- Page 6 Drill a 3/4″ (19 mm) hole for the electrical wire location. Route the electrical wiring from the dimmer switch through the hole in the finished wall. The wiring should extend at least 6″ (152 mm) from the hole. 1337912-2-A Kohler Co.
- Page 7 Using a 3/16″ drill bit, drill two holes at the marked locations on the finished wall. Insert the supplied anchors where needed. Position the power bar on the wall, with the electrical wire pulled through the large central hole. Verify the bar is level, then secure with two screws provided. Kohler Co. 1337912-2-A...
- Page 8 Connect the electrical wiring from the dimmer switch to the proper connectors on the power bar as shown. Feed the light cables through the slots and tape to the top of the power bar to keep the cables accessible for later connection. 1337912-2-A Kohler Co.
- Page 9 IMPORTANT! For K-99572-TLC and K-99573-TLC: Never leave the swinging panels unsupported during installation. For K-99572-TLC and K-99573-TLC: To ease installation, fold the swinging panels against the main mirror. Align the ″J″ hooks on the mirror with the slots in the power bar.
- Page 10 Lift the mirror up and out to disengage the ″J″ hooks from the power bar slots. Set the mirror aside. Using a 3/16″ drill bit, drill holes at the four marked locations on the finished wall. Insert the supplied anchors where needed. 1337912-2-A Kohler Co.
- Page 11 7. Secure the Mirror Reinstall the mirror to the power bar by engaging the ″J″ hooks with the slots. Refer to the ″Position the Mirror″ section. Secure the mirror to the finished wall with the four screws provided. Kohler Co. 1337912-2-A...
- Page 12 Use the dimmer switch to test the lights for proper operation. Install the Caps Press the caps to the top and bottom of the mirror. For K-99572-TLC and K-99573-TLC: Install the caps to the top and bottom of the swinging panels. 1337912-2-A Kohler Co.
-
Page 13: Care And Cleaning
Repeat the adjustments as needed. Care and Cleaning For best results, keep the following in mind when caring for your KOHLER product: NOTE: Periodic care and maintenance should include checking all hinge screws on the door to make sure that they are tight and engaged in the hinge holes.
Need help?
Do you have a question about the K-99572-TLC and is the answer not in the manual?
Questions and answers