Advertisement
Electric Bed Lift Kit
Workman
Model No. 08389
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
Note:
Determine the left and right sides of the machine from the normal operating position.
© 2023—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
MDX Lithium Utility Vehicle
Description
No parts required
Outboard-lift bracket (short flanges)
Inboard-lift bracket (long flanges)
Hex-head bolt (5/16 x 5-1/2 inches)
Flange nut (5/16 inch)
Switch
Hex washer head screw (#10 x 3/4 inch)
Relay
Lift actuator
Clevis pin (3-1/2 inches)
Clevis pin (2-1/4 inches)
Hairpin
Hex-head bolt (1/2 x 5-1/2 inches)
Locknut (1/2 inch)
No parts required
Foam pad
Register at www.Toro.com.
Form No. 3466-777 Rev A
Installation Instructions
Qty.
–
Prepare the machine.
1
1
Install the bed bracket.
1
1
1
2
Install the switch.
2
1
1
1
Install the lift actuator.
2
1
1
–
Remove the prop rod.
2
Install the foam pads.
Original Instructions (EN)
Printed in the USA
All Rights Reserved
Use
*3466-777*
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Toro 08389
Summary of Contents for Toro 08389
- Page 1 Form No. 3466-777 Rev A Electric Bed Lift Kit Workman ® MDX Lithium Utility Vehicle Model No. 08389 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine.
-
Page 2: Preparing The Machine
Lift the lever on either side of the cargo bed and lift the bed up (Figure Preparing the Machine No Parts Required Procedure Park the machine on a level surface. Engage the parking brake. Shut off the machine and remove the key. Turn the battery-disconnect switch to the O position (Figure... - Page 3 Pull the prop rod into the detent slot to secure the bed (Figure WARNING Installing the Bed-Lift A raised bed could fall and injure persons that are working beneath it. Brackets • Always use the prop rod to hold the bed up before working under the bed.
- Page 4 Align the left outboard-lift bracket (the bracket Insert the hex-head bolt (5/16 x 5-1/2 inches) with the short flanges) to the outboard holes in through the hole (8 mm or 5/16 inch) in the the upper- and lower-bed braces (Figure inboard-lift bracket (long flanges), bed structure, and the outboard bed-lift bracket (short flanges) Secure the outboard lift bracket to the bed using...
-
Page 5: Installing The Switch
Installing the Switch Parts needed for this procedure: Switch Hex washer head screw (#10 x 3/4 inch) Relay Procedure Cut out the opening in the dashboard decal for the switch. Install the switch connector through the opening in the dashboard. Route the switch to the switch connector. - Page 6 Secure the relays to the back of the dash with 2 hex washer head screws (#10 x 3/4 inch). g465068 Figure 9 1. Hex washer head screw (#10 x 3/4 inch) 2. Relay Installing the Lift Actuator Parts needed for this procedure: Lift actuator Clevis pin (3-1/2 inches) Clevis pin (2-1/4 inches)
- Page 7 Connect the 2-socket electrical connector of the Press the up paddle on the bed-lift switch to rear wire harness of the machine to the 2-pin extend the lift-actuator rod until the hole in the connector of the lift actuator (Figure 11).
- Page 8 Removing the Prop Rod No Parts Required Procedure WARNING A raised bed could fall and injure persons that are working beneath it. • Always use the prop rod to hold the bed up before working under the bed. • Remove any load material from the bed before raising it.
- Page 9 Fully lower the cargo bed and ensure that the cargo bed makes contact with the foam pads. If the cargo bed does not make contact with the foam pads in both locations, loosen the 4 cargo Installing the Foam Pads bed hinge bolts (Figure 16).
-
Page 10: Operation
Operation WARNING Driving the machine with the cargo bed raised could cause the machine to tip or roll easier. You could damage the structure of the cargo bed if you operate the machine with the bed raised. • Operate the machine when the cargo bed is down. - Page 11 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 12 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
Need help?
Do you have a question about the 08389 and is the answer not in the manual?
Questions and answers