Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for PO Fung Electronic NA-1901D Series
Summary of Contents for PO Fung Electronic NA-1901D Series
- Page 1 NA -1901D Series Digital Radio OWNER’S MANUAL English...
-
Page 2: Intended Use
Preface To help you ward off bodily injury or property loss that may arise from improper operation, please read all the information carefully before using our products. Intended Use Our products are designed to provide reliable wireless communication services for users across many industry sectors. In order to use the products safely and to achieve the best performance, they must be used as intended. -
Page 3: Fcc Regulations
Canada RSS102 Issue 5 March 2015 ● Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005 Edition RF Exposure Compliance and Control Guidelines and Operating Instructions To control your exposure and ensure compliance with the occupational/controlled environmental exposure limits, always adhere to the following procedures. Guidelines: ●... -
Page 4: Fcc Statement
requirements set forth in the above standards before they can be marketed in the U.S, and the manufacturer shall post a RF label on the product to inform users of operational instructions, so as to enhance their occupational health against exposure to RF energy. -
Page 5: Eu Regulatory Conformance
correspondantes. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: ● This device may not cause harmful interference. ● This device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. - Page 6 5. Do not operate the product in any area where use of wireless communication equipment is completely prohibited. ■ Important Tips To help you make better use of the product, be sure to observe the following instructions: 1. Do not use any unauthorized or damaged accessory. 2.
-
Page 7: Precautions For Batteries
Precautions for Batteries ■ Charging Prohibitions To protect you against any property loss, bodily injury or even death, be sure to observe the following safety instructions: 1. Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials. -
Page 8: Transportation Instructions
■ Transportation Instructions 1. Damaged batteries must not be transported. 2. To avoid short circuit, separate the battery from metal pars or from each other if two or more batteries are transported in one packaging. 3. The radio must be switched off and secured against switch-on, if the battery is attached. The content of the shipment must be declared in the shipping documents and by a Battery Shipping Label on the packaging. -
Page 9: Main Characteristics
Main characteristics • Encrypted calls (up to 32 key configurations), making calls more confidential • Speech noise reduction to significantly improve call quality in noisy environments • Support non-standard sub tone and frequency hopping functions, Enhance signal concealment and anti-interference ability •... -
Page 10: Main Controls And Parts Of The Radio
Main controls and parts of the radio 1.Antenna 2.SK1: Emergency alarm key 3.PTT key 4.SK2: Monitor key 5.SK3: Battery access key 6.Channel switch 7.Status Indicator (TX lights up red; RX lights up green) 8. Power switch/volume knob 9. Battery latch 10. -
Page 11: Charging The Battery
Charging the Battery Use the approved charger to charge the battery. Read the Safety Information Booklet before charging. Before initial use, fully charge the battery to ensure optimum performance. To charge the battery, do as follows: Insert the output connector of the power adapter into the port on the back of the charger. Plug the power adapter into a power outlet. - Page 12 ·To turn the radio off, rotate the control counter-clockwise till hearing a mechanical “click”. ·If voice prompts are enabled, they will be accompanied by "Power on and channel number". Select a Channel The radios can store up to 16 channels, and the channel type allows programming to analog or/and encrypted. In standby mode, turn the channel knob to select the channel you want.
-
Page 13: Monitor Function
Emergency Alarm In standby mode, press SK1 (Emergency Alarm key) to switch the emergency alarm function on/off. Monitor Function Before using the monitor function, check whether it is an analog channel. The monitor function is only available for analog channels. On analog channels, you can use SK2 (Monitor key) to hear weaker signals that are difficult to hear during normal operation, and to adjust the volume when there is no signal on the channel you have selected. - Page 14 Note: Channels that have not been added are not scanned. The radio will remain on the communication channel until that signal disappears. Scanning will resume 5 seconds after the signal disappears unless a new signal is detected within that delay time. Note: The scanning feature is only available if your local dealer has programmed at least two channels for the radios.
- Page 15 Turn on the prompt voice function, and there will be voice prompts when the encoder is turned on or operated. If you turn off the prompt voice function, there is only a “beep” prompt when you turn on or operate the encoder. The VOX feature enables hands free conversations without using PTT: just speak in the direction of the microphone and the communication will be automatically activated.
- Page 16 The receiver and transmitter prompt "beep" to enter wireless replication. When the transmitter presses the [PTT] key, the red light remains on, and the receiver green light automatically remains on. Copy all the configuration parameters of channels 1-16 of the transmitter, and the receiver prompts "beep" twice to complete the replication. Both prompt lights turn off and automatically restart, the replication task has ended.
-
Page 17: Troubleshooting Guide
function. • On the 15 channel, press and hold the [PTT]+[SK2] to turn on the radio and switch the prompt language between Chinese and English. -Channel scanning: any channel, hold down the [SK2] key to turn on radio to enter scanning. Trouble shooting guide PROBLEM SOLUTION... -
Page 18: Technical Specifications
Technical specifications General Frequency range 410~ 469 MHz Working temperature -20°/+55° C Operating voltage 7.4 V Data Rate for Digital 10250 bits per second Dimensions 59 x 37 x 130 mm (without antenna) Weight 240 g (Battery pack included) Antenna impedance 50Ω... - Page 19 We do not guarantee, for any particular purpose, the accuracy, validity, timeliness, legitimacy or completeness of the third-party products and contents involved in this manual. PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Add: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong E-mail: wangjianhui@baofengradio.com...
Need help?
Do you have a question about the NA-1901D Series and is the answer not in the manual?
Questions and answers