1. Manuals
  2. Brands
  3. PO Fung Electronic Manuals
  4. Radio
  5. NA-1909D Series
  6. Owner's manual

PO Fung Electronic NA-1909D Series Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
NA-1909D Series
Digital Radio
OWNER'S MANUAL
English

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NA-1909D Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for PO Fung Electronic NA-1909D Series

Summary of Contents for PO Fung Electronic NA-1909D Series

  • Page 1 NA-1909D Series Digital Radio OWNER’S MANUAL English...

  • Page 2: Intended Use

    Preface To help you ward off bodily injury or property loss that may arise from improper operation, please read all the information carefully before using our products. Intended Use Our products are designed to provide reliable wireless communication services for users across many industry sectors. In order to use the products safely and to achieve the best performance, they must be used as intended.

  • Page 3: Fcc Regulations

    Canada RSS102 Issue 5 March 2015 ● Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005 Edition RF Exposure Compliance and Control Guidelines and Operating Instructions To control your exposure and ensure compliance with the occupational/controlled environmental exposure limits, always adhere to the following procedures.

  • Page 4: Fcc Statement

    requirements set forth in the above standards before they can be marketed in the U.S, and the manufacturer shall post a RF label on the product to inform users of operational instructions, so as to enhance their occupational health against exposure to RF energy.

  • Page 5: Eu Regulatory Conformance

    correspondantes. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: ● This device may not cause harmful interference. ● This device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
  • Page 6 5. Do not operate the product in any area where use of wireless communication equipment is completely prohibited. ■ Important Tips To help you make better use of the product, be sure to observe the following instructions: 1. Do not use any unauthorized or damaged accessory. 2.

  • Page 7: Precautions For Batteries

    Precautions for Batteries ■ Charging Prohibitions To protect you against any property loss, bodily injury or even death, be sure to observe the following safety instructions: 1. Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials.

  • Page 8: Transportation Instructions

    ■ Transportation Instructions 1. Damaged batteries must not be transported. 2. To avoid short circuit, separate the battery from metal pars or from each other if two or more batteries are transported in one packaging. 3. The radio must be switched off and secured against switch-on, if the battery is attached. The content of the shipment must be declared in the shipping documents and by a Battery Shipping Label on the packaging.

  • Page 9: Main Characteristics

    Main characteristics • Encrypted calls (up to 32 key configurations), making calls more confidential • Speech noise reduction to significantly improve call quality in noisy environments • Support non-standard sub tone and frequency hopping functions, Enhance signal concealment and anti-interference ability •...

  • Page 10: Main Controls And Parts Of The Radio

    Main controls and parts of the radio 1.Antenna 2. PTT key 3. SK1: Monitor key 4. SK2: Battery access key 5. Channel switch 6. Power switch/volume knob 7. Accessory interface 8. Built-in speaker 9. Built-in microphone 10.Status Indicator (TX lights up red; RX lights up green) 11.

  • Page 11: Charging The Battery

    Charging the Battery Use the approved charger to charge the battery. Read the Safety Information Booklet before charging. Before initial use, fully charge the battery to ensure optimum performance. To charge the battery, do as follows: Insert the output connector of the power adapter into the port on the back of the charger. Plug the power adapter into a power outlet.

  • Page 12: Power On/Off And Volume Adjustment

    is off - charging is complete. When the charging indicator light at the bottom of the battery goes off, it indicates that the charging is complete. Remove the cable from the Type-C port at the bottom of the battery. Baofeng recommends your radio is turned off while being charged. Operations Power on/off and volume adjustment Rotate the [Power/Volume] knob clockwise to turn the radio on.

  • Page 13: Monitor Function

    to transmit when you are receiving a communication and use the transmission mode sparingly to allow other users to talk. Transmission consumes a significant amount of energy and should therefore be used sparingly to prolong the battery life. If you are unable to contact a station that you have no problems in receiving, the station may be using CTCSS tones or DCS codes.
  • Page 14 In standby mode, press and hold [SK1] key and then press [SK2] key briefly, it will broadcast the parameter information such as transmit frequency, receive frequency, CTCSS/DCS, transmit power, etc. stored in the current channel. Channel Scanning Note: Scanning can only be realized by setting the channel's scanning add to on through the CPS program software and turn on the unit's scanning function.
  • Page 15 voice on or off. Turn on the prompt voice function, and there will be voice prompts when the encoder is turned on or operated. If you turn off the prompt voice function, there is only a “beep” prompt when you turn on or operate the encoder. The VOX feature enables hands free conversations without using PTT: just speak in the direction of the microphone and the communication will be automatically activated.
  • Page 16 Quick group formation (Wireless clone function) Rotate the channel knob to channel 2, press and hold the [PTT]+[SK1] key to turn on both the transmitter and receiver. The receiver and transmitter prompt "beep" to enter wireless replication. When the transmitter presses the [PTT] key, the red light remains on, and the receiver green light automatically remains on.

  • Page 17: Troubleshooting Guide

    Accompanied by a voice prompt VOX On or VOX Off. • On the 10 channel, press and hold the [PTT]+[SK1] to turn on the radio and turn on or off the prompt voice function. • On the 15 channel, press and hold the [PTT]+[SK1] to turn on the radio and switch the prompt language between Chinese and English.

  • Page 18: Technical Specifications

    Technical specifications General Frequency range 410~ 469MHz Working temperature -20°/+55° C Operating voltage 7.4 V Data Rate for Digital 10248 bps in a 12.5 kHz channel Dimensions 65 x 41 x 148mm (without antenna) Weight 300 g (Battery pack included) Antenna impedance 50Ω...
  • Page 19 We do not guarantee, for any particular purpose, the accuracy, validity, timeliness, legitimacy or completeness of the third-party products and contents involved in this manual. PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong E-mail: wangjianhui@baofengradio.com...
  • Page 20 Print version: BF-1909D_V1.0...

Table of Contents