Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Dnake 280M-S8
Summary of Contents for Dnake 280M-S8
- Page 1 User Manual Model: 280M-S8 Indoor Monitor...
- Page 2 Remark Please follow the user manual for correct installation and testing. If there is any doubt please call our tech-supporting and customer center. Our company applies ourselves to reformation and innovation of our products. No extra notice for any change. The illustration shown here is only for reference.
-
Page 3: Table Of Contents
CATALOG Product Features............1 Technical Parameters..........1 Package Contents ............1 Pictures..............2 Operations..............3 1. Security..............4 2. Smart ..............11 3. Intercom .............14 4. Message .............16 5. Setup..............17 Web Settings ............20 System Configuration ..........22 System Diagram .............23 Installation ..............25 Troubleshooting .............26 Safety Instructions ..........27... -
Page 4: Product Features
Voltage: DC 12V Rated power: 9W Standby power consumption: 1.5W Display screen: 7'' Touch screen: Capacitive touch screen Resolution: 800x480 Working Temperature: -10℃ to +55℃ Storage Temperature: -10℃ to +60℃ Working Humidity: 10% to 90% (non-condensing) Package Contents User Manual Screws AB-280M-S8... -
Page 5: Pictures
Pictures 7'' capacitive touch screen Speaker Microphone... -
Page 6: Operations
Operations Main interface: Security, Smart, Intercom, Message and Setup. Status bar: Network connection and security precautions. Shortcut key: Do Not Disturb, Message, Records. Status bar instruction: 1. DND :Click icon, the system will enter DND or undo DND. You can use Do Not Disturb service when you don't want to be disturbed by calls(The valid time is 8 hours). -
Page 7: Security
1.Security Clicking “Security” icon on the main interface, the system will enter the following interface: 1.1 ON/OFF Clicking “ON/OFF” icon, the system will enter the following interface: 1.1.1 ON Click “Out” “Home”, or “Sleep” icon to activate the alarm sensors. The corresponding icon on the main interface will be lit up with a “Di-Di”... - Page 8 1.2 Camera Clicking “Camera” icon, the system will enter into the following interface: Click icon or icon button to select the camera you want, and then click monitor the IP camera. If you want to cancel monitoring, click to stop it. 1.2.1 IP Camera Setting Login the webpage of indoor monitor by username: user, password:1234, and then you can access the following webpage:...
- Page 9 Fill the RTSP format: rtsp:// user: password@ Camera IP . IP is the IP address of your IP Camera. Then you can monitor IP Camera in Security menu on your indoor monitor: Clicking “Camera” icon, the system will enter into the following interface: Click icon or icon button to select IP Camera to monitor, and then click...
-
Page 10: Alarm Type
Type Mode Delay Sensor 24 Hour Smoke Smoke 24 Hour Smoke 24 Hour 24 Hour Smoke Smoke 24 Hour Smoke 24 Hour 24 Hour Smoke Smoke 24 Hour 1.3.1 Alarm Type Clicking input box of type, a dialog box will pop up as below. On this interface, you can set alarm type as: Normal, Emergency or 24H. -
Page 11: Delay Time
Type Mode Delay Sensor 24 Hour Smoke Smoke 24 Hour Smoke 24 Hour 24 Hour Smoke 24 Hour Smoke Smoke 24 Hour BELL 24 Hour Smoke Smoke 24 Hour 1.3.3 Delay Time It refers to the delay time of giving an alarm. Clicking the setting box of Delay, it will pop up a dialog as follows: 0s, 5s, 15s, 20s, 25s, 40s or 60s. - Page 12 Type Mode Delay Sensor 24 Hour Smoke Smoke Smoke 24 Hour Smoke 24 Hour 24 Hour Smoke Door Smoke 24 Hour Window Smoke 24 Hour Panic 24 Hour Smoke Flood Smoke 24 Hour When alarm sensor is triggered, the indoor monitor will make a loud alarm sound, and the system will enter into the following interface as well as send alarm message to management center (if management center is installed in your system): You can see the No.
- Page 13 refers to Alarm ON, and refers to Alarm OFF. To set the sensor of alarm stations, you can click the corresponding station with icon. Click activation time to choose the corresponding time. The options of activation time include NONE, 30s, 40s, 60s, 100s and 300s.
-
Page 14: Smart
2.Smart Clicking “Smart” icon on the main interface, the system will enter into the following interface: 2.1 Scene Clicking “Scene” icon, the system will enter into the following interface: Scene mode includes: Home, Out , Dinner, Party and Sleep. 2.2 Light Clicking “Light”... - Page 15 Set the light of corresponding room, such as Master, Sub, Living and Dining Rooms (see the room setting for details). 8 lights can be set in every room at most. Clicking the corresponding light icon, you can turn the light ON/OFF. 2.3 Air Clicking “Air”...
- Page 16 2.4 Curtain Clicking “Curtain” icon, the system will enter into the following interface: By clicking “Close” icon, the curtain will be closed; by clicking “Open” icon, the curtain will be open; by clicking “Pause” icon, the curtain will be paused. 2.5 Elevator Clicking “Elevator”...
-
Page 17: Intercom
3.Intercom Clicking “Intercom” icon on the main interface, the system will enter into the following interface: 3.1 Call Out Clicking “Call Out” icon, the system will enter the following interface: 3.1.1 Call unit resident Input 1-3 digit building No.+ “Building” + 2-digit Unit No. + “Unit” +4-digit room No., then click icon to call. - Page 18 When answering the call, the system will enter into call status: Click icon to communicate with outdoor panel A; click icon to end the call; click icon to unlock the door. 3.1.2 Call management center Clicking “Center” icon to call management center, the system will call management center 1 to 5 sequentially.
-
Page 19: Message
Click “Door1” icon to switch outdoor panel or flat camera mode, then click icon to select the area you want to monitor, and click icon to monitor the outdoor panel or flat camera. Click icon to stop monitoring. Click icon to unlock the door. -
Page 20: Setup
Note: only by installing the management software on PC which is usually located at guard center, can indoor monitor receive the message sent by PC. Click icon to page up; click icon to page down; click icon to delete the record. - Page 21 123456 1501 5.3 Network Click “Network” icon, then input 1-16 digits password (the default password is 123456 ) to enter into the following interface: IP: the system will automatically display IP address of the indoor monitor. IP address is unique. The default Mask address is 255.255.255.0.
- Page 22 The Gateway in one system must be on the same segment. DNS: domain name resolution address (DNS of local operator). If indoor monitor is used on WAN, the address must be entered correctly; if it is used on LAN, the address can be ignored.
-
Page 23: Web Settings
Web Settings Please refer to 5.3 to view IP address. Connect the indoor monitor and computer by network switch. Input the indoor monitor’s IP address in the browser, then input user name and password (the default user name is “admin”, the password is “123456" to enter into the web setting interface). 1. - Page 24 Please refer to 5.2 for room settings. Click “Submit” icon to save the settings. 3. VOIP Click “VOIP” icon to enter into the following interface: The settings are the same with the ones of indoor monitor. To connect with SIP phone, check “Enable” and input the number registered in SIP server.
-
Page 25: System Configuration
System Configuration System Configuration CAT-5e+RVV2 CAT-5e+RVV2 Terminal Terminal *1.0 *1.0 Power 220V Power 220V Network Switch Network Switch CAT-5e CAT-5e Terminal Terminal Power Power 220V 220V RVV2*1.0 RVV2*1.0 Fiber Optical Fiber Optical Network Switch Network Switch Transceiver Transceiver RVV3*1.0 RVV3*1.0 Power Power 220V... -
Page 26: System Diagram
System Configuration System Diagram Network(POE) Power +12V GND RS485 Interface +12V 485+ Siren/Alarm 1. Power Power input interface connects with 12V power adapter. +12V +12V Power 12V Power 2. Network Connect with outdoor panel, indoor monitor or other network equipment by network switch. - Page 27 3. RS485 Connect with RS485 interface device; RS485 interface can output 12V/100mA power supply. If RS485 equipment to be connected doesn’t require the power supply, no need to connect +12V. +12V +12V RS485 Interface RS485 Equipment 4. Siren/Alarm When alarm sensor is triggered, the output power is 12V/100mA. Each interface of alarm zone can be connected with normally-open or normally -closed switch.
-
Page 28: Installation
System Configuration Installation Screws Built-in box Size: 221.4*151.4*16.5mm Installation Instructions: [Suggestion] During the installation, the camera should be 1450〜1550mm above the ground. The Wall camera tether for photographing human face should be the top priority. 400~500mm... -
Page 29: Troubleshooting
Troubleshooting The indoor monitor cannot start up or power off automatically. Check whether it has power-failure, and power it on again. The indoor monitor display screen is too dim. Check whether the brightness and contrast settings of screen are correct. No s ound d uring t he c ommunication. -
Page 30: Safety Instructions
Safety Instructions In order to protect you and others from harm or your device from damage, please read the following information before using the device. Do not install the device in the following places: Do not install the device in high-temperature and moist environment or the area close to magnetic field, such as the electric generator, transformer or magnet. - Page 31 V1.4 600110079604 Easy & Smart Intercom Solutions...
Need help?
Do you have a question about the 280M-S8 and is the answer not in the manual?
Questions and answers