Subscribe to Our Youtube Channel
Related Manuals for RightAngle New Heights Hover E
Summary of Contents for RightAngle New Heights Hover E
- Page 1 New Heights™ Hover E - Electric Monitor Arm Desktop Monitor Lift Assembly Instructions Warranty: raproducts.com/warranty Instruction #54385 • Dated: 01/24/2023 1 of 13...
- Page 2 READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT. USE THIS PRODUCT ONLY AS INSTRUCTED. FAILURE TO COMPLY WITH ALL INSTRUCTIONS AND WARNINGS MAY RESULT IN SERIOUS PROPERTY DAMAGE OR BODILY INJURY. WARNING Basic Safety Instructions Intended Use. This Product is exclusively designed for use as indoor office furniture in compliance with all instructions and safety warnings in the user manual.
-
Page 3: Tools Required For Assembly
Tools Required for Assembly Power Driver with Adjustable Torque Tape Measure #2 Phillips Head Driver Bit #2 Square Head Drive Bit (Recommended) Hardware Included for Assembly (may have extra) 5/8” Washer Head Wood Screw x2 5/8” Wood Screw x4 3/8” Bolt x4 M4 x 12mm Bolt x4 Cord Clip x1 Wire Management Channel x1... - Page 4 Step 1 • Slide the monitor lift assembly (T) onto the table top and tighten the knobs to secure it to the table. Step 2 • Install the control box (M) on the bottom side of the table using (2) wood screws (F). •...
- Page 5 Step 3 • Install the switch (N) on the bottom side of the table with (2) wood screws (F). NOTE: Screws do not • Attach cord clip (I) to the switch wire then install require pre-drilled holes. the clip to the table with (1) washer head wood screw (E).
- Page 6 Step 5 • Loosely attach (2) two hole weld nuts (P) to the Outside column bracket (Q) with (4) 3/8” bolts (G). Bolts Outside Bolts Do not fully tighten the (4) bolts. Turn Inside Bolts the bolts only a few times so they are just able to hold the (2) weld nuts.
- Page 7 Step 8 • Attach the (2) weld nuts (Y) to the rail mount (U) with (2) 1/2” bolts (X). Only insert the bolts a few turns so it is enough to hold the weld nut. • Slide the assembly into the slots in the rail to your desired location.
- Page 8 Step 10 • Slide the monitor arm onto the arm bracket until it clicks and is secured. NOTE: The Hover may vary depending on what is ordered. Step 11 • Install the monitor bracket to the back side of the monitor. Top of Bracket K&A Manufacturing •...
- Page 9 Step 12 • Slide the monitor bracket onto the monitor arm until it clicks and is secured. Step 13 • Install the Wire Managment on the back side of the rail. K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 9 of 13...
- Page 10 Step 14 • Attach the column top cap. • On the underside of the top cap, remove the backing of the double sided tape. Align the top cap to the top of the Hover E column - be sure to position the top cap correctly so the bolt at the top of the column correctly fits inside the top cap.
-
Page 11: Standard Switch
- To delete the lower container stop press You will hear a musical tone. Troubleshooting: If you are having any problems with the operation, contact RightAngle Products at 800.298.4351 or orders@raproducts.com K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 11 of 13... - Page 12 Optional Programmable Switch (full instructions packaged with switch) Start Up Procedure: • Plug the power cord into a standard 110V receptacle. A power surge protector is recommended. • Press the down arrow until the worksurface reaches its lowest position. • The workstation is ready for use. •...
- Page 13 Mechanical Reset Mode If the table is unresponsive, uneven, or not functioning properly, perform a manual reset. User settings are not reset in this process. There are three methods to reset a workstation: Reset Method A 1. Clear all obstructions from the travel path of the workstation 2.
Need help?
Do you have a question about the New Heights Hover E and is the answer not in the manual?
Questions and answers