1. Manuals
  2. Brands
  3. RightAngle Manuals
  4. Racks & Stands
  5. Hover E Glide
  6. Assembly instructions manual

RightAngle Hover E Glide Assembly Instructions Manual

Electric monitor lift
Hide thumbs

Advertisement

Table of Contents

Hover E Glide Electric Monitor Lift
Assembly Instructions
Instruction # 54709 • Updated: 06/22/2023

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Hover E Glide and is the answer not in the manual?

Questions and answers

Related Manuals for RightAngle Hover E Glide

Summary of Contents for RightAngle Hover E Glide

  • Page 1 Hover E Glide Electric Monitor Lift Assembly Instructions Instruction # 54709 • Updated: 06/22/2023...

  • Page 2: Basic Safety Instructions

    READ ALL INSTRUCTIONS BEFORE USING THESE PRODUCTS. USE THESE PRODUCTS ONLY AS INSTRUCTED. FAILURE TO COMPLY WITH ALL INSTRUCTIONS AND WARNINGS MAY RESULT IN SERIOUS PROPERTY DAMAGE OR BODILY INJURY. WARNING Basic Safety Instructions Intended Use. These products are exclusively designed for use as indoor office furniture in compliance with all instructions and safety warn- ings in the user manual.

  • Page 3: Tools Required For Assembly

    3/8-16 Nylock Nut x4 1/2” Self Tapping Screw x4 K. 3/16” Cable Clamp x1 5/8” Wood Screw x4 Parts M. Hover E Glide Assembly x1 N. Front Cover x1 O. Back Cover x1 Side Panels x2 Q. Control Switch x1 R.
  • Page 4 (M) on the top side of the worksurface. Align with the pre-drill pilot holes that were enlarged in the last step. • Do not slide the Hover E Glide along the worksurface to make sure the worksurface is not scratched. Top side of worksurface...

  • Page 5: Top View

    Step 3 • Insert four hex drive bolts (G) through the top side of the pre-drilled holes. • From the bottom side of the worksurface, attach four washers (H) and four Nylock nuts (I) to the bolts. • Using the 3/16” allen wrench (D) and the deep socket wrench (E), tighten all nuts to the bolts.
  • Page 6 Step 4 • Push the Hover E Glide assembly (M) to the back. • Insert the front cover (N) inside the Hover E Glide assembly. Step 5 • Pull the Hover E Glide assembly (M) to the front. • Align the holes on the Hover E Glide assembly and the front cover (N).
  • Page 7 Step 6 • Install one side panel (P) onto the Hover E Glide assembly (M) and attach using two self tapping screws (J). • Repeat on the other side. K&A Manufacturing • 800.298.4351 • raproducts.com...
  • Page 8 Step 7 • From the underside of the worksuface, mount the control box (R) to the worksurface using two 5/8” wood screws (L). • It can be installed in any location, wire lengths permitting. However, the long side of the control box MUST RUN PARALLEL to the long side of the worksurface.
  • Page 9 (K) and secure to the worksurface using a wood screw (F). • Attach the motor cable (located at the back of the Hover E Glide assembly (M)) to the control box. • Attach the power cable (S) to the control box. Route the power cord through the cable closet and plug into an outlet.
  • Page 10 Hover E Glide Monitor Rail & Arms Assembly Instructions K&A Manufacturing • 800.298.4351 • raproducts.com...
  • Page 11 Hardware and Tools Included for Assembly (may have extra) A. 3/16” Allen Wrench x1 B. 3mm Allen Wrench x1 C. 5/16-18 x 3/8” Bolt x D. M4 x 12mm Bolt x4 per monitor E. Two Hole Weld Nut x2 Single Hole Weld Nut x2 Parts G.
  • Page 12 Instruction Steps Step 1 • Attach two (2) two hole weld nuts (E) to the column mounting bracket (I) using four 5/16- 18 x 3/8” bolts (C) • Only turn the bolts a few times. The bolts should be a bit loose, but still holds the weld nut in place.
  • Page 13 • Select the position of the bracket and rail assembly. Tighten four bolts (C) on the outside of the column mounting bracket (I) to secure to the Hover E Glide Step 4 • Attach two single hole weld nuts (F) to each monitor rail bracket (J) using two .
  • Page 14 Step 5 • Install the monitor arm(s) (L) onto the monitor rail bracket (J). You will hear a click when the arm is properly attached. • No more than two arms should be attached to a single monitor rail bracket. •...
  • Page 15 Step 7 • Slide the monitor with monitor bracket onto the monitor arm. • You will hear a click when the bracket is securly attached to the arm. Have more than one monitor for the rail? Repeat steps 4 - 6. Step 6 •...
  • Page 16 Step 7 • Attach the column top cap (T) from the previous instruction set for the Hover E Glide Electric Monitor Lift. You may need to use a rubber mallet to carefully secure the cap to the column. K&A Manufacturing • 800.298.4351 • raproducts.com...
  • Page 17 4-Button Programmable Control Switch User Guide K&A Manufacturing • 800.298.4351 • raproducts.com...
  • Page 18 Control Switch Overview Enter Button 27.0 2-4 Keys Unused Display Arrow Keys During Program- ming Setting Memory Positions 1 - 4 Setting the Preset 1 button 1. Move the workstation to the desired height using the 2. Quickly press to enter the menu mode. is displayed and you will hear a musical tone.
  • Page 19 Setting the Preset 3 button 1. Move the workstation to the desired height using the 2. Quickly press to enter the menu mode. is displayed and you will hear a musical tone. 4. Press the to navigate the menu. 5. Navigate to the display 6.
  • Page 20 One Touch Memory Position One Touch Memory Position mode – On/Off What is One Touch/Short Press? One Touch/Short Press OFF: Press and hold the memory position buttons 1-4 until the workstation reaches its preset height. One Touch/Short Press ON Press memory position buttons 1-4 for 1 second and the workstation automatically reaches its preset height.
  • Page 21 Upper & Lower Container Stops Setting Upper and Lower Container Stops Container stops allow the user to limit the travel of the workstation to avoid collision with common under desk and over desk items such as file cabinets, chairs, upper shelf, counter tops, etc. NOTE: Container stops can be added and deleted at any time.

  • Page 22: Troubleshooting

    Removing the Upper and Lower Container Stops Removes the existing container stops from memory. Removing Lower Container Stop 1. Move the workstation to its lowest position by pressing and holding the until it stops moving. 2. Quickly press to enter the menu mode. is displayed and you will hear a musical tone.
  • Page 23 Mechanical Reset Mode If the table is unresponsive, uneven, or not functioning properly, perform a manual reset. User settings are not reset in this process. There are three methods to reset a workstation: Reset Method A 1. Clear all obstructions from the travel path of the workstation 2.

Table of Contents